innova_Use-Maintenance---Innova-Auto_714

Bu sayfa, kılavuzun PDF dosyasındaki metnin tamamıdır (sayfa sayfa). Görseller ve çizimler için PDF'i açın. — sibastore.com

Sayfa 1

 
INNOVA 60 B 2013 
INNOVA 65-75-85-100 B 2013 

 
ORIGINAL 
INSTRUCTIONS 
Doc. 10029401 
Ver. 
AD 
 
 
 

USE AND MAINTENANCE MANUAL 

INNOVA 70 S 2013 

ED. 08-2020 
ENG

Sayfa 3

The descriptions contained in this document are not binding.  
The company therefore reserves the right to make any modifications at any time to 
elements, details, or accessory supply, as considered necessary for reasons of 
improvement or manufacturing/commercial requirements. 
The reproduction, even partial, of the text and drawings contained in this document is 
prohibited by law. 
The company reserves the right to make any technical and/or supply modifications. 
The images are for reference purposes only, and are not binding in terms of design 
and supply. 
 
Symbols used in the manual 
 

Open book symbol with an "i": 
Indicates the need to consult the instruction manual 

Open book symbol: 
Used to tell the operator to read the manual before using the 
machine 

Warning symbol 
Carefully read the sections marked with this symbol and observe 
the indications, for the safety of the operator and the machine 

Warning symbol 
Indicates danger of gas exhalation and leakage of corrosive 
liquids 

Warning symbol 
Indicates the danger of fire. 
keep naked flames at a safe distance 

Warning symbol 
Indicates that the packed product should be handled with 
suitable lifting means that comply with the legal requirements 

Disposal symbol 

Carefully read the sections marked with this symbol, for machine 

disposal

Sayfa 4

 
ON CONSIGNMENT OF THE MACHINE............................................................................................................................................. 6 
INTRODUCTORY COMMENT ............................................................................................................................................................ 6 
INTENDED USE ............................................................................................................................................................................... 6 
SERIAL NUMBER PLATE ................................................................................................................................................................. 6 
TECHNICAL DESCRIPTION .............................................................................................................................................................. 7 
SYMBOLS USED ON THE MACHINE ................................................................................................................................................ 8 
GENERAL SAFETY REGULATIONS ............................................................................................................................................... 13 
PREPARATION OF MACHINE ........................................................................................................................................................ 15 

1. HANDLING THE PACKED MACHINE............................................................................................................................................................. 15 
2. HOW TO UNPACK THE MACHINE ................................................................................................................................................................ 15 
3. HOW TO MOVE THE MACHINE .................................................................................................................................................................... 15 
4. INSTRUMENT PANEL COMPONENTS (Innova 60B version) ........................................................................................................................... 16 
5. INSTRUMENT PANEL COMPONENTS (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70BTO versions) ...................................... 16 
6. INSTRUMENT PANEL COMPONENTS (Innova 70S version) ........................................................................................................................... 16 
7. STEERING COLUMN COMPONENTS (Innova 60B version) ............................................................................................................................ 17 
8. STEERING COLUMN COMPONENTS ........................................................................................................................................................... 17 
9. FOOTBOARD COMPONENTS ...................................................................................................................................................................... 17 
10. SIDE COMPONENTS OF THE MACHINE .................................................................................................................................................... 18 
11. REAR COMPONENTS OF THE MACHINE ................................................................................................................................................... 19 
12. BATTERY TYPE ........................................................................................................................................................................................ 19 
13. BATTERY MAINTENANCE AND DISPOSAL ................................................................................................................................................ 19 
14. FITTING THE BATTERIES INTO THE MACHINE .......................................................................................................................................... 20 
15. CONNECTING THE BATTERIES AND BATTERY CONNECTOR ................................................................................................................... 21 
16. CONNECTING THE BATTERY-CHARGER (VERSIONS WITHOUT BUILT-IN BATTERY CHARGER) ............................................................... 21 
17. CONNECTING THE BATTERY-CHARGER (VERSIONS WITH A BUILT-IN BATTERY CHARGER) ................................................................... 22 
18. HOUR METER (Innova 60B versions) .......................................................................................................................................................... 23 
19. HOUR METER (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO versions) .................................................... 24 
20.  BATTERY CHARGE LEVEL INDICATOR (Innova 60B versions) .................................................................................................................... 24 
21.  BATTERY CHARGE LEVEL INDICATOR (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO versions) ............. 24 
22. WORKING FORWARD SPEED ................................................................................................................................................................... 24 
23. FILLING THE SOLUTION TANK WITH WATER ............................................................................................................................................ 25 
24. DETERGENT SOLUTION (VERSION WITHOUT CDS) .................................................................................................................................. 26 
25. FILLING THE DETERGENT CANISTER (VERSION WITH CDS) .................................................................................................................... 26 
26. ASSEMBLING THE SQUEEGEE (Innova 60B versions) ................................................................................................................................. 28 
27. ASSEMBLING THE SQUEEGEE (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO versions) .......................... 29 
28. ASSEMBLING THE BRUSH HEAD CARTER (Innova 65B - Innova 75B - Innova 85B - Innova 100B versions) .................................................... 29 
29. ASSEMBLING THE BRUSH (Innova 60B versions) ........................................................................................................................................ 30 
30. ASSEMBLING THE BRUSHES (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO versions) ............................. 31 
31. ASSEMBLING THE BRUSH (Innova 70S versions) ........................................................................................................................................ 31 
32. PARKING BRAKE – SERVICE BRAKE......................................................................................................................................................... 32 
33. BLINKING LIGHT (OPTIONAL) .................................................................................................................................................................... 32 
PREPARING TO WORK .................................................................................................................................................................. 33 

34.  PREPARING TO WORK (versions without CDS) .......................................................................................................................................... 33 
35.  PREPARING TO WORK (versions with CDS) ............................................................................................................................................... 34 
WORK ........................................................................................................................................................................................... 37 

36. BEGINNING TO WORK (Innova 60B versions) .............................................................................................................................................. 37 
37. BEGINNING TO WORK (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO versions) ....................................... 38 
38. DETERGENT REGULATION (VERSION WITHOUT CDS) ............................................................................................................................. 42 
39. DETERGENT REGULATION (VERSION WITH CDS) .................................................................................................................................... 42 
40. ADJUSTING THE FORWARD WORKING SPEED (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO versions) .. 44 
41. WATER MANAGEMENT KIT (Innova 60B versions)....................................................................................................................................... 44 
42. "ECO" DEVICE (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO versions) ................................................... 45 
43. EXTRA BRUSH HEAD BODY PRESSURE (Innova 65B - Innova 75B - Innova 85B versions) ............................................................................ 45 
44. OVERFLOW DEVICE (Innova 60B versions) ................................................................................................................................................. 46 

CONTENTS 

4

Sayfa 5

45. OVERFLOW DEVICE (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO versions) .......................................... 47 
AT THE END OF THE WORK .......................................................................................................................................................... 48 
DAILY MAINTENANCE ................................................................................................................................................................... 50 

46. EMPTYING THE RECOVERY TANK ............................................................................................................................................................ 50 
47. DRAINING THE SOLUTION TANK (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70BTO versions) ........................................... 50 
48. DRAINING THE SOLUTION TANK (Innova 70S versions) .............................................................................................................................. 51 
49. CLEANING THE SQUEEGEE BODY ............................................................................................................................................................ 52 
50. CLEANING THE DISC BRUSHES (Innova 60B versions) ............................................................................................................................... 53 
51. CLEANING THE DISC BRUSHES (Innova 65B - Innova 75B - Innova 85B - Innova 100B versions) .................................................................... 54 
52. CLEANING THE CYLINDRICAL BRUSH (Innova 70S versions) ...................................................................................................................... 55 
53. CLEANING THE DEBRIS HOPPER (Innova 70S versions) ............................................................................................................................. 56 
54. CLEANING THE RECOVERY TANK FILTER ................................................................................................................................................ 57 
WEEKLY MAINTENANCE ............................................................................................................................................................... 58 

55. CLEANING THE RECOVERY TANK ............................................................................................................................................................ 58 
56. CLEANING THE SOLUTION TANK (Innova 65B – Innova 75B – Innova 85B – Innova 100B – Innova 70BTO versions) ....................................... 58 
57. CLEANING THE SOLUTION TANK (Innova 70S versions) ............................................................................................................................. 59 
58. CLEANING THE WATER SYSTEM FILTER .................................................................................................................................................. 60 
59. CLEANING THE VACUUM TUBE (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70BTO versions) ............................................. 61 
60. CLEANING THE VACUUM TUBE (Innova 70S versions) ................................................................................................................................ 62 
61. CLEANING THE DETERGENT CANISTER (versions with CDS) ..................................................................................................................... 63 
EXTRAORDINARY MAINTENANCE ................................................................................................................................................ 65 

62. REPLACING THE SQUEEGEE RUBBER BLADES (Innova 60B versions) ....................................................................................................... 65 
63. REPLACING THE SQUEEGEE RUBBER BLADES (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70BTO versions) .................... 66 
64. ADJUSTING THE SQUEEGEE (Innova 60B versions) ................................................................................................................................... 67 
65. ADJUSTING THE SQUEEGEE (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO versions) ............................. 68 
66. REPLACING THE DISC BRUSH (Innova 60B versions) ................................................................................................................................. 69 
67. REPLACING THE DISC BRUSHES (Innova 65B - Innova 75B - Innova 85B - Innova 100B versions) ................................................................. 69 
68. REPLACING THE CYLINDRICAL BRUSH (Innova 70S versions) .................................................................................................................... 70 
69. REPLACING THE BRUSH HEAD CARTER (Innova 65B - Innova 75B - Innova 85B - Innova 100B versions) ...................................................... 71 
70. CLEANING THE DOSING SYSTEM (VERSIONS WITH CDS) ........................................................................................................................ 72 
TROUBLESHOOTING ..................................................................................................................................................................... 76 

71. INSUFFICIENT WATER ON THE BRUSHES ................................................................................................................................................ 76 
72. THE SQUEEGEE DOES NOT DRY PERFECTLY .......................................................................................................................................... 76 
73. THE MACHINE DOES NOT CLEAN WELL ................................................................................................................................................... 76 
74. EXCESSIVE FOAM PRODUCTION ............................................................................................................................................................. 76 
75. THE VACUUM CLEANER DOES NOT FUNCTION ........................................................................................................................................ 76 
76. THE BRUSH MOTOR DOESN'T WORK (INNOVA 60B VERSIONS) ............................................................................................................... 77 
77. THE BRUSH MOTOR DOES NOT WORK .................................................................................................................................................... 77 
78.  IT IS IMPOSSIBLE TO RAISE OR LOWER THE BRUSH HEAD OR SQUEEGEE ............................................................................................ 77 
79. THE MACHINE DOES NOT START ............................................................................................................................................................. 77 
80. ELECTRIC FUSES AND THERMAL CUT-OUTS ........................................................................................................................................... 78 
81. THE AUTOMATIC WATER/DETERGENT DOSING SYSTEM DOES NOT WORK ............................................................................................ 78 
DISPOSAL ..................................................................................................................................................................................... 79 
CHOOSING AND USING THE BRUSHES ......................................................................................................................................... 80 
EC DECLARATION OF CONFORMITY ............................................................................................................................................ 81 
UKCA DECLARATION OF CONFORMITY ....................................................................................................................................... 83 

5

Sayfa 6

On consignment of the machine 
 

When the machine is consigned to the customer, an immediate check 
must be performed to ensure all the material mentioned in the shipping 
documents has been received, and also to check the machine has not 
suffered damage during transportation. If this is the case, the carrier 
must ascertain the extent of the damage at once, informing our 
customer service office. It is only by prompt action of this type that the 
missing material can be obtained, and compensation for damage 
successfully claimed. 

Introductory comment  

Innova 60B – Innova 65B – Innova 75B – Innova 85B – Innova 100B 
– Innova 70S – Innova 70BTO is a floor scrubbing machine that, thanks 
to the mechanical action of two disc brushes (or cylindrical, depending 
on the chosen version) and the chemical action of a water-detergent 
solution, can handle a wide variety of floors and types of dirt. As it 
moves forward, it collects the dirt removed and also the detergent 
solution not absorbed by the floor. 
The machine must only be used for this purpose. Even the best 
machines will only work well if used correctly and kept in good working 
order. We therefore suggest you read this instruction booklet carefully, 
and read it again whenever difficulties arise while using the machine. If 
necessary, remember that our customer assistance service (organised 
in collaboration with our dealers) is always available for advice or direct 
intervention. 
Intended use 
The floor scrubbing machine is designed for the professional cleaning of 
surfaces and floors in industrial, commercial and public environments 
only. It is only suitable for use in closed (or at least covered) places. 
The machine is not suitable for use in the rain, or under water jets. IT IS 
FORBIDDEN to use the machine for picking up dangerous dusts or 
inflammable liquids in places with an explosive atmosphere. In addition, 
it is not suitable as a means of transport for people or objects. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Serial number plate 

The serial number plate is located at the rear of the steering column, 
and indicates the general characteristics of the machine, in particular the 
serial number of the machine. The serial number is an extremely 
important piece of information and should always be provided together 
with any request for assistance or to purchase spare parts. 

6

Sayfa 7

TECHNICAL DESCRIPTION 
U/M 
Innova 

70S 
Innova 
70BTO 
Working width 
mm 
610 
650 
750 
850 
1010 
690 
710 
Squeegee width 
mm 
780 
970 
970 
1085 
1085 
970 
970 
Working capacity, up to 
m2/h 
3660 
3900 
4500 
5100 
6000 
4100 
4200 
Disc brushes 
No. /  mm 
1/610 
2/340 
2/390 
2/430 
2/510 
 
 
Cylindrical brushes 
No. /  mm 
 
 
 
 
 
1/210 
 
Abrasive pad 
No. / mm 
 
 
 
 
 
 
1/710x355 
Brush rpm 
rpm 
170 
170 
170 
170 
120 
520 
3500 
Brush motor 
V/W 
24/450 
24/500 
24/500 
24/500 
24/600 
24/560 
24/600 
Maximum pressure on the brushes (min/max) 
kg 
30 
30/60 
30/60 
30/60 
30 
20 
30/60 
Traction motor 
V/W 
24/400 
Traction wheel 
 mm 
220 
Forward speed 
km/h 
0÷6 
Maximum gradient with full load 
% 
10 
Suction motor 
V/W 
24/410 
Suction vacuum 
mbar 
91 
Rear elastic wheels 
 mm 
300 
Solution tank 
l 
110 
Recovery tank 
l 
125 
Detergent tank (CDS version only) 
l 
- 
                                                 5 
Steering diameter 
mm 
1910 
Machine length (without squeegee) 
mm 
1495 
Machine height (without optional blinking light kit) 
mm 
1320 
Machine width (without squeegee) 
 
Solution 

Battery compartment dimensions (l x w x h) 
mm 
385x525x350 
Rated battery voltage 
V 
24 
Battery weight (max) 
kg 
136 
Machine weight (empty and without batteries) 
kg 
213 
213 
213 
213 
230 
233 
233 
Machine weight during transport (machine + batteries + 
brushes + squeegee) 
kg 
350 
350 
350 
350 
366 
370 
370 

Machine weight in running order (machine + batteries + 
water + brushes + squeegee + operator) 
kg 
420 
420 
420 
420 
436 
440 
440 

Sound pressure level (ISO 11201) 
dB (A) 
<70 
<70 
<70 
<70 
<70 
<70 
<70 
Uncertainty Kpa 
dB (A) 
1.5 
1.5 
1.5 
1.5 
1.5 
1.5 
1.5 

60B 
Innova 

65B 
Innova 

75B 
Innova 

85B 
Innova 

100B 
Innova 

mm 
680 
680 
770 
855 
1035 
805 
805 

7

Sayfa 8

Indicates the maximum gradient. 

Pedal labels that indicate the forward and reverse direction of the machine. 
Used to indicate the direction of the machine. 

Water quantity regulation symbol. 
Used on the steering column to indicate the knobs for adjusting the quantity of water distributed in the machine's water system. 

Symbol denoting pressure applied to the brushes. 
Used to indicate the pedal to increase the pressure on the brushes. 

Parking brake symbol. 
Used on the machine to indicate the parking brake control lever. 

Symbol indicating the maximum temperature of the water used to fill the solution tank. 

Symbol indicating the position of the solution tank drain pipe. 

Symbol indicating the position of the recovery tank drainage tube. 

Label with instructions for the use of standard or concentrated detergents (CDS system only). 

SYMBOLS USED ON THE MACHINE 

8

Sayfa 9

Label with warnings on the type of detergent to use (CDS system only). 

Label with Ph value of the detergent to use (CDS system only). 

Indicates the risk of crushed hands. 

Main switch symbol (key switch). 
Used on the instrument panel, to indicate the key switch for machine operation on (ON/I) or off (OFF/0). 

Type of battery technology used (Innova 60B versions). 
Used on the control display to indicate the type of battery programmed into the machine's control circuit board. 

Type of hour meter and service (Innova 60B versions). 
Used on the control display, in the top line to indicate the type of hour meter programmed into the machine's control circuit board. 
Whereas the bottom line displays the type of service programmed into the machine's control circuit board. 

Battery charge level indicator and hour meter (Innova 60B versions). 
Used on the control display, in the top line, to indicate the charge condition of the batteries. Whereas in the bottom line there is the 
machine's total operating hours. 

Symbol of brush head / squeegee moving to the idle position (Innova 60B versions). 

Used to indicate the movement linkage of the brush head and squeegee 

Symbol of brush head / squeegee moving to the work position (Innova 60B versions). 

Used to indicate the movement linkage of the brush head and squeegee 

SYMBOLS USED ON THE MACHINE 

9

Sayfa 10

Horn symbol (Innova 60B versions).

It is used in the rear of the steering column to indicate the horn button.

Brush head / squeegee operating symbol (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO
versions).
Used to indicate the I-DRIVE program selector.

ECO mode symbol (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO versions).
Used on the control panel to indicate the button that activates the ECO mode of the machine.

Horn symbol (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO versions).
Used on the control panel, to indicate the horn button.

Symbol for water amount regulation (CDS system only).
Used on the control panel to indicate the button regarding the regulation of the water level inside the machine's water circuit.

Water level symbol (CDS system only).
Used on the control display to indicate the water level in the machine's water circuit.

Detergent percentage adjustment symbol (CDS system only).
Used on the control panel to indicate the button pertaining to the regulation of the percentage of detergent inside the machine's water
circuit.

Detergent percentage level symbol (CDS system only).
Used on the control display to indicate the percentage of detergent in the machine's water circuit.

Symbol for the values for dosing the detergent solution (CDS system only).
Used on the control panel to indicate the variation of the "water amount level" symbols in relation to the water in the machine's water
system. And the variation of the “detergent percentage level” in relation to the detergent percentage in the machine's water system.

SYMBOLS USED ON THE MACHINE

Sayfa 11

Brush uncoupling symbol (Innova 65B - Innova 75B - Innova 85B versions).
Used on the control panel to indicate the button for uncoupling the brushes.

Brush uncoupling symbol (Innova 65B - Innova 75B - Innova 85B versions).
Used on the control display to indicate that the brushes are being uncoupled.

Forward/reverse speed adjuster symbol (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO versions).
Used on the control panel, to indicate the button that allows you to regulate the forward or reverse speed of the machine.

Forward/reverse speed symbol (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO versions).
Used on the control display, to indicate the level of speed of the forwards or reverse of the machine.

Battery charge level symbol (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO versions).
Used on the control display to indicate the state of charge of the batteries.

Critical battery charge level symbol (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO versions).
Used on the control display to indicate the critical state of charge of the batteries and the need to recharge them.

“DRYING” program symbol (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO versions).
Used in the control display to indicate that the “DRYING” working program is active, in this case only the suction motor is operating.

“ECO DRYING” program symbol (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO versions).
Used in the control display to indicate that the “ECO-DRYING” working program is active, in this case only the suction motor is
operating in economic mode.

“SCRUBBING-DRYING” program symbol (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO
versions).
Used in the control display to indicate that the “SCRUBBING-DRYING” working program is active, in this case the brush motor, the
solenoid valve and the suction motor are operating.

SYMBOLS USED ON THE MACHINE

Sayfa 12

“ECO SCRUBBING-DRYING” program symbol (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO
versions).
Used in the control display to indicate that the “ECO SCRUBBING-DRYING” working program is active, in this case the brush motor,
the solenoid valve and the suction motor are operating in economic mode.

“EXTRA PRESSURE SCRUBBING-DRYING” program symbol (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S -
Innova 70BTO versions).
Used in the control display to indicate that the “SCRUBBING-DRYING-EXTRA PRESSURE” working program is active, in this case the
brush motor, the solenoid valve and the suction motor are operating.

“ECO EXTRA PRESSURE SCRUBBING-DRYING” program symbol (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova
70S - Innova 70BTO versions).
Used in the control display to indicate that the “ECO SCRUBBING-DRYING-EXTRA PRESSURE” working programme is active, in this
case the brush motor, the solenoid valve and the suction motor are operating, and with the addition of extra pressure on the brushes in
economic mode.

“SCRUBBING” program symbol (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO versions).
Used in the control display to indicate that the “SCRUBBING” working program is active, in this case the brush motor and the solenoid
valve are operating.

“ECO SCRUBBING” program symbol (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO versions).
Used in the control display to indicate that the “ECO SCRUBBING” working program is active, in this case the brush motor and the
solenoid valve are operating in economic mode.

“EXTRA PRESSURE SCRUBBING” program symbol (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova
70BTO versions).
Used in the control display to indicate that the “SCRUBBING-EXTRA PRESSURE” working program is active, in this case the brush
motor and the solenoid valve are operating, but with the addition of more pressure on the brushes.

“ECO EXTRA PRESSURE SCRUBBING” program symbol (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S -
Innova 70BTO versions).
Used in the control display to indicate that the “ECO SCRUBBING-EXTRA PRESSURE” working program is active, in this case the
brush motor and the solenoid valve are operating, but with the addition of more pressure on the brushes in economic mode.

Symbol for active parking brake (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO versions).
Used in the control display to indicate that the parking brake is engaged.

Symbol for active battery-charger (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO versions with
built-in battery-charger).
Used in the control display to indicate that the battery charger is operating and is carrying out the recharge cycle.

SYMBOLS USED ON THE MACHINE

Sayfa 13

GENERAL SAFETY REGULATIONS

The regulations below must be carefully followed in order to avoid harm to the operator and damage to the
machine.

WARNING:
• Read the labels on the machine carefully. Do not cover them for any reason and replace them immediately if they
become damaged.
• The machine must be exclusively used by authorised, trained personnel.
• Do not use the machine on surfaces with an inclination greater than the one shown on the plate.
• The machine is not suitable for cleaning rough or uneven floors. Do not use the machine on slopes.
• If the power supply cable of the battery charger is damaged, contact an Authorised service centre immediately.
• In case of danger, disconnect the battery connector on the rear of the machine.
• For all maintenance interventions, switch off the machine and disconnect the battery connector and/or the power
supply cable.
• Children must be supervised to ensure they do not play with the device.
• During the working of the machine, pay attention to other people and especially to children.
• Only use the brushes supplied with the machine, or those specified in the "CHOOSING AND USING THE
BRUSHES" paragraph of the instruction manual. The use of other brushes could compromise safety levels.

ATTENTION:
• The machine is not suitable for use by children and persons with reduced physical, mental and sensory
capabilities, or people who lack experience and knowledge.
• The machine must not be used or stored outdoors, in damp conditions or directly exposed to rain.
• The storage temperature must be between -25C and +55C; do not store outdoors in damp conditions.
• Conditions of use: room temperature between 0°C and 40°C with relative humidity between 30 and 95%.
• The socket for the machine's power cable (electric version) or for the battery charger power cable (battery
version) must be correctly earthed.
• Adapt the speed to the adhesion conditions.
• Do not use the machine as a means of transport.
• The machine does not cause harmful vibrations.
• Do not use the machine in an explosive atmosphere.
• Do not vacuum inflammable liquids.
• Do not use the device to collect dangerous powders.
• Do not mix different types of detergent as this may produce harmful gases.
• The machine is not suitable for cleaning carpets.
• Do not place any liquid containers on the machine.
• Avoid working with the brushes when the machine is standing still, so as not to damage the floor.
• In the event of a fire, use a powder extinguisher. Do not use water.
• Do not knock against shelving or scaffolding, where there is a danger of falling objects. The operator must always
be equipped with the appropriate safety devices (gloves, shoes, helmet, goggles, etc.).
• The machine is designed to carry out the scrubbing and drying operations simultaneously. Different operations
should only be carried out in areas where the passage of unauthorised persons is prohibited. Signal the presence
of damp floors with suitable signs.
• If the machine does not work properly, check this is not caused by failure to carry out routine maintenance.
Otherwise, ask for intervention of the authorised technical assistance centre.
• If you need to replace any components, request the ORIGINAL spare parts from an Authorised dealer and/or
Retailer.

Sayfa 14

• Restore all electrical connections after any maintenance interventions. 
• Before using the machine, check that all the hatches and covers are positioned as shown in this Use and 
Maintenance Manual. 
• Do not remove the guards that can only be removed with the aid of tools, except for maintenance work (see the 
relevant paragraphs) 
• Do not wash the machine with direct water jets or with pressurised water, nor with corrosive substances. 
• To prevent scaling in the solution tank filter, do not fill the tank with detergent solution many hours before using 
the machine. 
• Do not use acid or basic solutions that could damage the machine and/or harm people. 
• Have the machine checked by an authorised technical assistance centre every year. 
• When disposing of consumable materials, observe the laws and regulations in force. 
• When your machine has reached the end of its long working life, dispose of the materials it contains (especially 
oils, batteries and electronic components) in an appropriate manner, taking into account that the machine itself 
was constructed using 100% recyclable materials. 
• The batteries must be removed from the machine before its disposal. The batteries must be disposed of in a safe 
manner, fully observing the laws and regulations in force. 

14

Sayfa 15

PREPARATION OF MACHINE

1. HANDLING THE PACKED MACHINE

The machine is contained in specific packaging with a pallet for the handling with fork trucks. The
packages CANNOT be placed on top of each other.
The overall weight of the package (machine without batteries, plus packaging elements) is:

Innova

60B
Innova

65B
Innova

75B
Innova

85B
Innova

100B
Innova

70S
Innova
70BTO

268kg
268kg
268kg
268kg
285kg
288kg
288kg

The packaging dimensions are as follows:

Innova

A: 1635 mm

B: 730 mm

C: 1600 mm

2. HOW TO UNPACK THE MACHINE

1. Remove the outer package.
2. The machine is fixed to the pallet with wedges which block the wheels.
3. Remove the wedges.
4. Use a chute to get the machine down from the pallet, pushing it backwards. Do not assemble the rear
squeegee before unloading the machine, and avoid violently jolting the brush head. To assemble the
squeegee, read the section “ASSEMBLING THE SQUEEGEE”.

5. Keep the pallet for any future transport needs.

ATTENTION: If the product is delivered in cardboard containers, handle the
packed product with suitable lifting means that comply with the legal requirements

ATTENTION: During this operation, check there are no people or objects near the
machine

3. HOW TO MOVE THE MACHINE

1.
Using a chute, mount the machine on the pallet. Carry out this operation with the rear squeegee
and the brushes detached from the machine.
2.
Check the solution tank and recovery tank are empty; if necessary, empty them.
3.
Make sure that the main switch of the machine is in the "0" position; if not, position it to "0".
4.
Disconnect the electric system connector from the battery connector.
5.
Secure the machine to the pallet using wooden wedges.
6.
Engage the parking brake.

C
B

Sayfa 16

4. INSTRUMENT PANEL COMPONENTS (Innova 60B version) 

The instrument panel components are identified as follows: 

1. 
Battery level / hour meter display 
2. 
Battery level hour meter display control button 
3. 
Main key switch 
4. 
Red warning light indicating that the parking brake is on 

5. INSTRUMENT PANEL COMPONENTS (Innova 65B - Innova 75B - Innova 85B - Innova 100B - 
Innova 70BTO versions) 

The instrument panel components are identified as follows: 

1. 
Main key switch. 
2. 
Emergency switch. 
3. 
Working program adjustment switch, I-Drive device. 
4. 
Command display. 

Choose the desired working program with the I-Drive device: 

A. Transfer: movement of the machine without working. 
B. Drying: using the squeegee only. 
C. Scrubbing / Drying: using both the brushes and the squeegee. 
D. Scrubbing only : using the brushes only. 

5. 
"ECO" function button. 
6. 
Horn button. 
7. 
Selector button of the level of the water amount in the water system (only CDS system). 
8. 
Selector button for the level of the forward and reverse speed. 
9. 
"BRUSH UNCOUPLING" function button. 
10. Selector button for the percentage of detergent in the water system (only CDS system). 

6. INSTRUMENT PANEL COMPONENTS (Innova 70S version) 

The instrument panel components are identified as follows: 

1. 
Main key switch. 
2. 
Emergency switch. 
3. 
Working program adjustment switch, I-Drive device. 
4. 
Command display. 

MACHINE PREPARATION 

16

Sayfa 17

Choose the desired working program with the I-Drive device: 

A. Transfer: movement of the machine without working. 
B. Drying: using the squeegee only. 
C. Scrubbing / Drying: using both the brushes and the squeegee. 
D. Scrubbing only : using the brushes only. 

5. 
"ECO" function button. 
6. 
Horn button. 
7. 
Selector button of the level of the water amount in the water system (only CDS system). 
8. 
Selector button for the level of the forward and reverse speed. 
9. 
Selector button for the percentage of detergent in the water system (only CDS system). 

7. STEERING COLUMN COMPONENTS (Innova 60B version) 

The steering column components are identified as follows: 

1. 
Squeegee body lifting lever 
2. 
Brush head unit lifting lever 
3. 
Horn button 
4. 
Detergent solution adjustment lever 

8. STEERING COLUMN COMPONENTS 

The steering column components are identified as follows: 

1. 
Detergent solution adjustment lever (version without CDS) - clean water adjustment lever (version 
with CDS). 

9. FOOTBOARD COMPONENTS 

The footboard components are identified as follows: 

1. 
Accelerator pedal, forward. 
2. 
Accelerator pedal, reverse. 
 

ATTENTION: Only by simultaneously pressing the pedals is the reverse made 

MACHINE PREPARATION 

17

Sayfa 18

3. 
Service brake pedal. 
4. 
Parking brake lever. 
 

5. 
Pedal for extra brush head pressure (Innova 65B - Innova 75B - Innova 85B - Innova 100B 
versions). 
6. 
Water level pipe (versions with CDS) or solution level pipe (versions without CDS). 
 

10. SIDE COMPONENTS OF THE MACHINE 

The side components of the machine are identified as follows: 

1. 
Water-detergent filler cap (versions without CDS), water filler (versions with CDS). 
2. 
Fast water filler cap. 
3. 
Optional kit for cleaning accessories. 

4. 
Optional rapid refill kit. 

5. 
Solution tank dumping system tube (Innova 60B - Innova 65B - Innova 75B - Innova 85B - Innova 
100B - Innova 70BTO versions). 
 

6. 
Solution tank dumping system cap (Innova 70S versions). 
 

MACHINE PREPARATION 

18

Sayfa 19

7.
Vacuum cap.
8.
Optional blinking light kit.

11. REAR COMPONENTS OF THE MACHINE

The rear components of the machine are identified as follows:

1.
Recovery tank drainage tube.
2.
Squeegee vacuum hose.

12. BATTERY TYPE

To power the machine it is necessary to use:

• liquidelectrolyte lead traction batteries;
• sealed traction batteries with gas recombination or gel technology.
OTHER TYPES MUST NOT BE USED.
The batteries must meet the requirements laid out in the norms: CEI EN 60254-1:2005-12 (CEI 21-5) +
CEI EN 60254-2:2008-06 (CEI 21-7)
The battery compartment can house four 6V or two 12V batteries
For a good operating performance, we suggest the use of 210 Ah C5 batteries

13. BATTERY MAINTENANCE AND DISPOSAL

For maintenance and recharging, respect the instructions provided by the battery manufacturer.
Particular attention must be paid when choosing the battery charger, if not supplied, since there are
different kinds according to the type and capacity of the battery.
When the battery reaches the end of its working life, it must be disconnected by expert, trained personnel,
then lifted, using the grips and suitable lifting devices, to remove it from the battery compartment.
EXHAUSTED BATTERIES ARE CLASSIFIED AS DANGEROUS WASTE AND MUST BE CONSIGNED
TO THE AUTHORISED BODIES FOR CORRECT DISPOSAL.

ATTENTION: users are advised to always wear protective gloves, to avoid the
risk of serious injury to hands.

ATTENTION: You are advised to only lift and move the batteries with lifting and
transportation means suitable for the specific weight and size.

MACHINE PREPARATION

Sayfa 20

14. FITTING THE BATTERIES INTO THE MACHINE

The batteries must be housed in the special compartment beneath the recovery tank and should be
handled using lifting equipment that is suitable in terms of both weight and coupling system. They must
also satisfy the requirements of Standard CEI 21-5. The dimensions of the battery compartment are: 384 x
520 x H340 mm.

ATTENTION: for battery maintenance and daily recharging, you must fully respect
the indications provided by the manufacturer or retailer. all installation and
maintenance operations must be carried out by specialized personnel.

ATTENTION: make sure that you comply with the accident prevention regulations
in force in the country where you work or with DIN EN 50272-3 and DIN EN 50110-
1, before any handling of the batteries.
ATTENTION: to prevent an accidental short circuit use insulated tools to connect
the batteries, and do not place or drop metal objects on the battery. Remove rings,
watches and any clothing with metal parts that may come into contact with the
battery terminals.

To insert the batteries into the compartment proceed as follows:

1.
Check that the recovery tank is empty; if not, empty it using the tube provided for this purpose (01)
positioned at the rear of the machine (read the section "EMPTYING THE RECOVERY TANK").
2.
Block the machine in place by engaging the parking brake, press the pedal (02) and block it with the
lever (03) at the rear of the steering column (read the section “PARKING BRAKE AND SERVICE
BRAKE”).
3.
Check the main switch (04) is at "0", if not, turn the key by a quarter of a turn to the left, and remove
the key from the instrument panel.

4.
Grip the handle on the right side of the recovery tank.
5.
Lift the recovery tank until it hooks to the end of the safety catch.

ATTENTION: Before installing the battery, clean the battery compartment with a
damp cloth. Check that the connectors on the cables supplied are functioning
correctly.
ATTENTION: check that the characteristics of the battery that you are looking to use
are appropriate for the type of work to be performed. Check the battery charge and
the condition of the contacts on the battery.

ATTENTION: You are advised to only lift and move the batteries with lifting and
transportation means suitable for the specific weight and size.

ATTENTION: the lifting hooks must not damage the blocks, connectors or cables.

6.
House the batteries in the compartment, positioning the poles “+” and “-“ opposite each other.

ATTENTION: Before inserting the batteries into the machine, remember to cover the
terminals with a little grease to protect them against external corrosion.

ATTENTION: You are advised to use airtight batteries only, to avoid the leakage of
acids!

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of
serious injury to hands.

PREPARATION OF MACHINE

Sayfa 21

15. CONNECTING THE BATTERIES AND BATTERY CONNECTOR

1.
Connect the batteries in series using the jumper cables supplied (03) to the poles “+” and “-“.
2.
Connect the battery connector cable (01) to the “+” and “-“ poles to obtain a voltage of 24V on the
terminals.
3.
Connect the battery connector (01) to the machine connector (02).

ATTENTION: All installation and maintenance operations must be carried out by
expert personnel, trained at the specialised assistance centre.
ATTENTION: users are advised to always wear protective gloves, to avoid the risk of
serious injury to hands.

4.
Remove the safety catch.
5.
Grip the handle on the right side of the recovery tank, lower the tank until it is in the work position.

16. CONNECTING THE BATTERY-CHARGER (VERSIONS WITHOUT BUILT-IN BATTERY
CHARGER)

In order not to cause permanent damage to the batteries, it is essential to avoid their complete discharge:
arrange the recharge within a few minutes of the switching on of the "discharged batteries" blinking light.

ATTENTION: Never leave the batteries completely discharged, even if the machine
is not being used. Check the battery charger is suitable for the batteries installed, in
terms of both capacity and type.

To connect the battery charger you must:

1.
Move the machine near to the battery charger.
2.
Check that the recovery tank is empty; if not, empty it using the tube provided for this purpose (01)
positioned at the rear of the machine (read the section "EMPTYING THE RECOVERY TANK").
3.
Block the machine in place by engaging the parking brake, press the pedal (02) and block it with the
lever (03) at the rear of the steering column (read the section “PARKING BRAKE AND SERVICE
BRAKE”).

4.
Check the main switch (04) is at "0", if not, turn the key by a quarter of a turn to the left, and remove
the key from the instrument panel.
5.
Grip the handle on the right side of the recovery tank.
6.
Lift the recovery tank until it hooks to the end of the safety catch.

ATTENTION: Park the machine in an place protected from the weather and with
suitable ventilation, and on a flat and level surface; near the machine there must be
no objects that could either damage it, or be damaged through contact with it.

7.
Disconnect the electric system connector (05) from the battery connector (06).

ATTENTION: This process must be carried out by qualified personnel. An incorrect
connection of the connector may cause a malfunction of the device.

MACHINE PREPARATION

Sayfa 22

8.
Connect the battery charger cable (07) to the battery connector (06).
9.
Grip the handle on the safety catch and turn the recovery tank until it hooks up with the prop in the
first point of the safety catch.

The coupling connector of the battery charger is supplied inside the bag containing this instruction
booklet, and must be fitted to the battery charger cables as shown in the instructions.

10. Connect the recently wired cable to the external battery charger.
11. After a full recharge cycle, grip the handle on the right side of the recovery tank until it hooks to the
first prop of the safety catch.
12. Connect the battery connector (06) to the electric system connector (05).
13. Grip the handle on the safety catch and lower the recovery tank until it is in the work position.

ATTENTION: carefully read the use and maintenance instructions of the battery
charger that is used for charging.
ATTENTION: Keep the recovery tank open for the duration of the battery recharging
cycle to allow gas fumes to escape
ATTENTION: the room used to recharge the batteries must be adequately ventilated
to prevent the accumulation of gases that leak from batteries.
ATTENTION: every time a battery recharging cycle is enabled, you are advised to
raise the cap (8) until the hook (9) can be fixed to the prop (10) of the recovery tank.

ATTENTION: Danger of gas exhalation and leakage of corrosive liquids.

ATTENTION: Danger of fire: keep naked flames at a safe distance

17. CONNECTING THE BATTERY-CHARGER (VERSIONS WITH A BUILT-IN BATTERY
CHARGER)

ATTENTION: Never leave the batteries completely discharged, even if the
machine is not being used. Check the battery charger is suitable for the
batteries installed, in terms of both capacity and type.

To connect the battery charger you must:

1.
Take the machine to the maintenance area.
2.
Check that the recovery tank is empty; if not, empty it using the tube provided for this purpose (01)
positioned at the rear of the machine (read the section "EMPTYING THE RECOVERY TANK").
3.
Block the machine in place by engaging the parking brake, press the pedal (02) and block it with
the lever (03) at the rear of the steering column (read the section “PARKING BRAKE AND
SERVICE BRAKE”).

MACHINE PREPARATION

Sayfa 23

7.
Remove the cover (05) of the battery charger.
8.
Connect the connector of the battery charger power cable to the socket (06) on the charger itself.
9.
Plug the battery charger power cable into the mains socket.
10. Grip the handle on the safety catch and turn the recovery tank until it hooks up with the prop in the
first point of the safety catch.

ATTENTION: keep the recovery tank open for the duration of the battery recharging
cycle to allow gas fumes to escape.
ATTENTION: the room used to recharge the batteries must be adequately ventilated to
prevent the accumulation of gases that leak from batteries.
ATTENTION: Before inserting the battery charger power cable into the socket, verify
that there is no condensate or other forms of liquids.

11. After a full recharge cycle, grip the handle on the right side of the recovery tank until it hooks to the
first prop of the safety catch.
12. Pull out the battery charger power cable from the mains socket.
13. Disconnect the connector of the battery charger power cable from the socket (06) on the battery
charger itself.
14. Secure the cover (05) of the battery charger.
15. Grip the handle on the safety catch and lower the recovery tank until it is in the work position.

ATTENTION: Carefully read the use and maintenance manual of the charger that is
delivered inside the bag containing this instruction booklet.

ATTENTION: if the electrical system of the machine is accidentally powered, the
command display will visualise the symbol shown in the adjacent figure and none of
the steering wheel commands will work. Valid for Innova 65B - Innova 75B - Innova
85B - Innova 100B - Innova 70S - Innova 70BTO versions only.
ATTENTION: Always make sure the green LED of the battery charger is on before
using the machine again

18. HOUR METER (Innova 60B versions)

The control display is on the machine's instrument panel, the third screen after the machine has been
started allows you to observe, in the lower part of the screen, the hours and minutes the machine has
been operating. The flashing “:” symbol indicates that the hour meter is counting the machine functioning
time.

MACHINE PREPARATION

Sayfa 24

MACHINE PREPARATION

19. HOUR METER (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova
70BTO versions)

The control display is on the machine's instrument panel, the third screen after the machine has been
started allows you to observe:

1.
In the first part of the display you can display the work voltage that has been set and the type of
battery.

2.
In the second part of the display you can display the total time (first sequence of numbers) and the
partial time (second sequence of numbers) that the machine has been used. The numbers followed
by the letter “h” identify the hours, while the numbers followed by the letter “m” identify the tenths of
an hour (a tenth of an hour corresponds to six minutes).
3.
In the third part of the display you can display the program version of the controls circuit board.

20. BATTERY CHARGE LEVEL INDICATOR (Innova 60B versions)

The control display is on the machine's instrument panel, the third screen after the machine has been
started allows you to observe, in the top part of the screen, the state of charge of the batteries.
When the batteries supplied are fully charged, the upper line contains 8 light indicators that represent a
battery. As the batteries gradually run down, the indicators go out and, with the batteries completely run
down, only the battery outline flashes.

21. BATTERY CHARGE LEVEL INDICATOR (Innova 65B - Innova 75B - Innova 85B - Innova 100B
- Innova 70S - Innova 70BTO versions)

The control display is on the machine's instrument panel, in the top right of the work screen is the graphic
symbol (01) that identifies the charge level indicator of the batteries. The indicator is composed of 5
charge levels, each of which represents about 20% of residual charge. With a residual charge of 20% the
graphic symbol starts to flash and after a few second it will appear in larger dimensions in the middle of
the screen, under these conditions take the machine to the usual place to charge the batteries.

ATTENTION: a few seconds after the battery charge level reaches 20%, the
brush motor switches off automatically. With the remaining charge it is still
possible, however, to complete the drying process before recharging

ATTENTION: a few seconds after the battery charge level reaches 10%, the
suction motor switches off automatically. With the remaining charge, it is still
possible, however, to move the machine to the location designated for its
recharging

22. WORKING FORWARD SPEED

This machine is equipped with electronic traction control. To move the machine, after having turned the
key in the ON position, push the drive pedal (01) adjusting the speed by pressing and releasing the pedal.
The machine will then start moving. To make a reversing manoeuvre, press both pedals (01 and 02), the
machine will then start moving backwards. During reverse motion, the machine emits an acoustic signal.

Sayfa 25

23. FILLING THE SOLUTION TANK WITH WATER 

Before filling the solution tank, carry out the following steps: 

1. 
Take the machine to the usual place for filling the solution tank  
2. 
Check that the recovery tank is empty; if not, empty it using the tube provided for this purpose (01) 
positioned at the rear of the machine (read the section "EMPTYING THE RECOVERY TANK"). 

ATTENTION: The tanks should be emptied in the place used for draining dirty water. 

 
3. 
Block the machine in place by engaging the parking brake, press the pedal (02) and block it with 
the lever (03) at the rear of the steering column (read the section “PARKING BRAKE AND 
SERVICE BRAKE”). 

4. 
Turn the main machine switch to "0" by turning the key (04) a quarter rotation to the left. 
5. 
Remove the key from the instrument panel. 

6. 
Check that the solution tank discharge plug (05) has been tightened, if not turn it in an anticlockwise 
direction. (Innova 60B - Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70BTO 
versions). 

7. 
Check that the solution tank discharge plug (05) has been tightened, if not turn it in an anticlockwise 
direction. (Innova 70S versions) 

8. 
Check that the cap of the water system filter (06) on the front right of the machine, has been 
tightened, if not turn it in an anticlockwise direction. 

MACHINE PREPARATION 

25

Sayfa 26

The solution tank can be filled with water in three different ways:

1.
By unscrewing the filler cap (01) and filling it using a rubber tube or bucket.

ATTENTION: Check that the filter (02) under the filler cap (01) is positioned correctly;
this is to prevent impurities and dirt causing a malfunction in the machine's water
system.

2.
By using the rubber cap (03), which supports the water hose on its own, be sure to unscrew the cap
(01) to allow the proper vent of air.

3.
By using the optional system (05) for automatically topping up with clean water, which has a float
for controlling the overflow, be sure to unscrew the cap (01) to allow the proper vent of air.

ATTENTION: Before inserting the female insert into the male insert (05) in the rapid
top-up kit, be sure to remove the cap (04).

Fill with clean water, at a temperature not higher than 50C and not lower than 10°C. The amount
inside the tank can be seen by means of the level tube (04) on the front left of the seat.

24. DETERGENT SOLUTION (VERSION WITHOUT CDS)

After filling the solution tank with clean water add the liquid detergent to the tank in the concentration and
manner indicated on the detergent manufacturer's label. To prevent the formation of an excessive amount
of foam that could damage the vacuum motor, use the minimum percentage of detergent required.

ATTENTION: Always use detergents whose manufacturer's label indicates their
suitability for scrubbing machines. Do not use acid or alkaline products or solvents
without this indication.

ATTENTION: protective gloves should always be worn before handling detergents or
acidic or alkaline solutions, to avoid serious injury to the hands.

ATTENTION: always use low-foam detergent. To avoid the production of foam, put a
minimum quantity of antifoam liquid in the recovery tank before starting to clean. Do
not use pure acids.

25. FILLING THE DETERGENT CANISTER (VERSION WITH CDS)

After filling the solution tank with clean water, proceed as follows:

1.
Open the hatch (01) on the front of the steering column.

PREPARATION OF MACHINE

Sayfa 27

2.
Remove the cap (02) of the detergent canister (03).

3.
Remove the machine's detergent canister (03).
4.
Fill the canister with the desired detergent, in the manner set out on the label coming with the
machine.

ATTENTION: protective gloves should always be worn before handling detergents or
acidic or alkaline solutions, to avoid serious injury to the hands.

ATTENTION: always use low-foam detergent. To avoid the production of foam, put a
minimum quantity of antifoam liquid in the recovery tank before starting to clean. Do
not use pure acids.

ATTENTION: Always use detergents whose manufacturer's label indicates their
suitability for scrubbing machines. Do not use acid or alkaline products or solvents
without this indication. In addition, you are advised to always use low foam
detergents. Do not use pure acids or detergents with a stronger gradation than that
indicated on the label supplied.

5.
Put back the canister in the chamber inside the steering column.
6.
Properly close the screw cap (02) to prevent liquid coming out when working, and make sure that
the detergent suction filter is properly positioned on the bottom of the canister.

7.
Close the hatch (01) on the front of the steering column.
8.
Before starting to use the machine for the first time carefully read the sections “REGULATING THE
DETERGENT (versions with CDS)” and “PRIMING THE DETERGENT SOLUTION PUMP (versions
with CDS)”.

ATTENTION: the dosing system is suitable for frequent maintenance cleaning. Acid
or alkaline maintenance detergent can be used with pH values between 4 and 10 and
that do not contain: oxidising agents, chlorine or bromine, formaldehyde, mineral
solvents. The detergents used must be suitable for use with scrubbing machines.
Wash the circuit with water after use if the system is not used daily. The system can
be excluded. In case of sporadic use of detergents with pH between 1-3 or 11-14,
use the floor scrubbing machine in the traditional way by adding the detergent in the
clean water tank and excluding the dosing circuit.

PREPARATION OF MACHINE

Sayfa 28

26. ASSEMBLING THE SQUEEGEE (Innova 60B versions) 

To assemble the squeegee, which for reasons of packaging, is supplied dismantled from the machine, 
proceed as follows: 

1. 
Block the machine in place by engaging the parking brake, press the pedal (01) and block it with 
the lever (02) at the rear of the steering column (read the section “PARKING BRAKE AND 
SERVICE BRAKE”). 

2. 
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left. 
3. 
Remove the key from the instrument panel. 
 

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of 
serious injury to hands. 

4. 
Check that the squeegee attachment is raised from the floor, if necessary turn the lever (04) 
clockwise. 
 

5. 
Initially insert the right pin (05) of the squeegee into the right slot (06) of the squeegee attachment, 
making sure to keep the spring and the washer above the squeegee attachment plate.  
 

ATTENTION: This can be simplified by first loosening the handwheel (07) on the pin. 

6. 
Repeat the same operation for the left pin. 
7. 
Then tighten the handwheels (07) to lock the squeegee in place. 
8. 
Finally insert the vacuum hose (08) of the squeegee into the relative coupling (09) of the vacuum 
nozzle. 

ATTENTION: The squeegee has already been regulated, however if it needs 
adjusting, read the sections “REGULATING THE SQUEEGEE” and “REGULATING 
THE SQUEEGEE ATTACHMENT”. 

PREPARATION OF MACHINE 

28

Sayfa 29

27. ASSEMBLING THE SQUEEGEE (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova
70S - Innova 70BTO versions)

To assemble the squeegee, which for reasons of packaging, is supplied dismantled from the machine,
proceed as follows:

1.
Check that the squeegee attachment is raised from the floor, if not, use the switch on the
instrument panel.
2.
Block the machine in place by engaging the parking brake, press the pedal (01) and block it with
the lever (02) at the rear of the steering column (read the section “PARKING BRAKE AND
SERVICE BRAKE”).

3.
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left.
4.
Remove the key from the instrument panel.

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of
serious injury to hands.

5.
Initially insert the right pin (04) of the squeegee into the right slot (05) of the squeegee attachment,
making sure to keep the spring and the washer above the squeegee attachment plate.

ATTENTION: This can be simplified by first loosening the handwheel (06) on the pin.

6.
Repeat the same operation for the left pin.
7.
Then tighten the handwheels (06) to lock the squeegee in place.
8.
Finally insert the vacuum hose (07) of the squeegee into the relative coupling (08) of the vacuum
nozzle.

ATTENTION: The squeegee has already been regulated, however if it needs
adjusting, read the sections “REGULATING THE SQUEEGEE” and “REGULATING
THE SQUEEGEE ATTACHMENT”.

28. ASSEMBLING THE BRUSH HEAD CARTER (Innova 65B - Innova 75B - Innova 85B - Innova
100B versions)

The brush head casings, for reasons of packaging, are supplied dismantled from the machine, so to
assemble to the brush head unit proceed as follows:

1.
Check that the brush head unit is in contact with the floor, if not, use the switch on the control panel.
2.
Block the machine in place by engaging the parking brake, press the pedal (01) and block it with
the lever (02) at the rear of the steering column (read the section “PARKING BRAKE AND
SERVICE BRAKE”).

PREPARATION OF MACHINE

Sayfa 30

3.
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left.
4.
Remove the key from the instrument panel.

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of
serious injury to hands.

5.
Insert the left casing (04) on the brush head unit, securing it on it using the screws (05) supplied.
6.
Repeat the same operation also for the right casing.

ATTENTION: This operation must be carried out by qualified personnel, using suitable
equipment. An incorrect connection may cause the machine to malfunction.

29. ASSEMBLING THE BRUSH (Innova 60B versions)

To assemble the brush, which for reasons of packaging is supplied dismantled from the machine, proceed
as follows:

1.
Block the machine in place by engaging the parking brake, press the pedal (01) and block it with
the lever (02) at the rear of the steering column (read the section “PARKING BRAKE AND
SERVICE BRAKE”).

2.
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left.
3.
Remove the key from the instrument panel.

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of
serious injury to hands.

4.
Check that the brush head unit is raised from the floor, if necessary turn the lever (04)
anticlockwise.

5.
With the brush head in a high position put the brush in the housing of the plate under the brush
head, turning it until the three buttons go into the niches of the plate itself; Turn until the pin is
pushed towards the coupling spring and is locked into place.

PREPARATION OF MACHINE

Sayfa 31

30. ASSEMBLING THE BRUSHES (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova
70S - Innova 70BTO versions)

To assemble the brushes, which for reasons of packaging are supplied dismantled from the machine,
proceed as follows:

1. Block the machine in place by engaging the parking brake, press the pedal (01) and block it with the
lever (02) at the rear of the steering column (read the section “PARKING BRAKE AND SERVICE
BRAKE”).

2. Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left.
3. Remove the key from the instrument panel.

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of
serious injury to hands.

4. With the brush head up, insert the brushes in the plate housing beneath the brush head, turning them
until the three pins enter the niches in the plate itself; Turn until the pin is pushed towards the coupling
spring and is locked into place. The photo shows the rotation direction to hook up the left-hand brush;
for the right-hand one, rotate in the opposite direction.

31. ASSEMBLING THE BRUSH (Innova 70S versions)

To assemble the brushes, which for reasons of packaging are supplied dismantled from the machine,
proceed as follows:

1. Block the machine in place by engaging the parking brake, press the pedal (01) and block it with the
lever (02) at the rear of the steering column (read the section “PARKING BRAKE AND SERVICE
BRAKE”).

2. Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left.
3. Remove the key from the instrument panel.

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of
serious injury to hands.

4. With the brush head in a high position remove the right brush head casing (04), uncoupling the
retention hinges (05).

PREPARATION OF MACHINE

Sayfa 32

5. Insert the brush (the side with 5 teeth) in the tunnel until it couples with the drive hub on the opposite 
side of the tunnel. 
 

6. Insert the idler wheel of the right brush head casing in the brush. 
7. Secure the right casing (04) to the brush head using the retention hinges (05). 

ATTENTION: Pay attention to the direction of the brush bristles during assembly, the 
cusp of the brush viewed from the above should be towards the front of the machine. 

32. PARKING BRAKE – SERVICE BRAKE 

The machine has an electronic braking system. To brake in normal conditions, just remove your foot from 
the accelerator pedal. If this service brake is working badly, or if necessary, activate the brake pedal (01) 
pushing it downwards.  
 
 

To engage the parking brake, press the brake pedal (01) downwards then pull the lever (02) to the left 
until the pedal (01) is locked in place. The command display will visualise the symbol shown in the figure 
(Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO versions only). 
 

ATTENTION: With the parking brake engaged the traction motor is disengaged, only 
by removing the parking brake is it possible to move forwards or backwards. 

33. BLINKING LIGHT (OPTIONAL) 

The machine can be equipped with a blinking light that turns on automatically when the key in the main 
switch is turned on. 

PREPARATION OF MACHINE 

32

Sayfa 33

34.  PREPARING TO WORK (versions without CDS) 

Before beginning to work, it is necessary to: 

1. Make sure the recovery tank is empty, otherwise empty it completely. 
2. Check that the quantity of detergent solution in the solution tank is correct for the type of work to be 
carried out; if not, refill the solution tank. View the level tube (01) on the front left of the seat. 

3. Check that the state of the squeegee rubber is suitable for work, if not have them maintained (read 
the sections “CLEANING THE SQUEEGEE RUBBER” or else “REPLACING THE SQUEEGEE 
RUBBER”). 

4. Check that the state of the disc brush/brushes (Innova 60-65-75-85-100 B versions) or the cylindrical 
brush (Innova70 S versions) are suitable for work, if not have them maintained (read sections 
“CLEANING THE BRUSH” or else “REPLACING THE BRUSH”). 

5. Grip the handle on the right side of the recovery tank. 
6. Lift the recovery tank until it hooks to the end of the safety catch. 

7. Check that the connector of the general system (02) is connected to the battery connector (03), if not, 
connect them together. 
 
 

 
 
8. Grip the handle on the right side of the recovery tank. 
9. Lower the recovery tank as far as the working position. 
 

PREPARING TO WORK 

2 

3 

33

Sayfa 34

35.  PREPARING TO WORK (versions with CDS) 

Before beginning to work, it is necessary to: 

1. Make sure the recovery tank is empty, otherwise empty it completely. 
2. Check that the quantity of water in the solution tank is sufficient for the type of work to be carried out; 
if not, refill the solution tank. View the level tube (01) on the front left of the seat. 

3. Check that the amount of detergent in the canister (02) is sufficient for the type of work you want to 
carry out, if not, fill up with detergent (read the section “FILLING THE CANISTER WITH 
DETERGENT”). 

4. Check that the state of the squeegee rubber is suitable for work, if not have them maintained (read 
the sections “CLEANING THE SQUEEGEE RUBBER” or else “REPLACING THE SQUEEGEE 
RUBBER”).  

5. Check that the state of the brushes (Innova 65-75-85-100 B versions) or the cylindrical brush 
(Innova70 S versions) are suitable for work, if not, have them maintained (read sections “CLEANING 
THE BRUSH” or else “REPLACING THE BRUSH”). 

6. Grip the handle on the right side of the recovery tank. 
7. Lift the recovery tank until it hooks to the end of the safety catch. 

8. Check that the connector of the general system (03) is connected to the battery connector (04), if not, 
connect them together. 
9. Grip the handle on the right side of the recovery tank. 
10. Lower the recovery tank as far as the working position. 
 

PREPARING TO WORK 

3 

4 

34

Sayfa 35

11. Make sure that the tap is fully open, the knob (05) should be completely down. 

12. Make sure that the bypass tap (06) on the brush head is in the "dosing system" position. 

13. Turn the main machine switch to "I", turn the key (07) a quarter rotation to the right. 

14. When the work screen appears on the control display, press the button (08) for water flow regulation. 

15. Set the maximum amount of water in the detergent solution, by pressing the button (08) until the 
symbol shown on the side is completely full. 

16. After regulating the amount of water in the detergent solution, press the button (09) to regulate the 
dispensing percentage level of the dosing system. 

PREPARING TO WORK 

35

Sayfa 36

17. Set the maximum amount of chemical in the detergent solution, by pressing the button (09) until the 
symbol shown on the side is completely full. 

18. Select the “WASHING/ DRYING” program, by rotating the switch to “C”. 

19. Gently press the forward pedal (10) to activate the brush head and the dosing system. 
 

ATTENTION: As soon as you press the pedal (10) the machine will start to move, the 
brush head and the squeegee will come down into contact with the floor and will start 
working, at the same time the solenoid valve and the dosing system will dispense the 
detergent solution. 

 
 
 
20. Wait a few moments, keeping the accelerator pedal gently depressed (normally 40 - 60 seconds) to 
allow the system to engage. 
21. Proceed with the desired adjustment for normal scrubbing (read the section“REGULATING THE 
DETERGENT SOLUTION (versions with CDS)”). 

PREPARING TO WORK 

36

Sayfa 37

36. BEGINNING TO WORK (Innova 60B versions)

To start working, do as follows:

1.
Make all the checks listed in “PREPARING TO WORK”.
2.
Sit on the driver’s seat.
3.
Turn the main switch key (01) clockwise by a quarter of a turn to "I". The control display on the
instrument panel will immediately comes on.

When the display comes on, three screens appear in sequence. The first screen shows (on the top line)
what type of hour meter has been set; in this case it is a total hour meter (to display a different type - for
instance partial - contact the qualified, COMAC-trained personnel). The bottom line shows the “service”
setting (in this case there is no setting).

The second screen displays what battery technology has been set for machine operation; in this case it
is lead batteries (to set another type of battery - for instance gel - contact the qualified, COMAC-trained
personnel).

The third and last screen (known as “work”) displays the battery charge status and the total functioning
time. When the batteries supplied are fully charged, the upper line contains 8 light indicators that
represent a battery. As the batteries gradually run down, the indicators go out and, with the batteries
completely run down, only the battery outline flashes. The bottom line indicates the hours and minutes
of functioning. The flashing “:” symbol indicates that the hour meter is counting the machine functioning
time.

4.
Pull the knob (04) down and adjust the amount of solution desired.

5.
Lower the brush head until it comes into contact with the floor, rotating the lever (05) in a clockwise
direction.

WORK

Sayfa 38

6.
Lower the brush head until it comes into contact with the floor, rotating the lever (06) in an anti-
clockwise direction.

7.
Remove the parking brake, turn the lever (07) clockwise. In the control panel the red indicator light
pertaining to the parking symbol “P” will go out.

ATTENTION: If you try to move forward with the parking brake engaged, the machine
will not move because the motor wheel is disengaged electrically when the parking
brake is active.

8.
Pressing the forward movement pedal (08), the machine will start to move.

As soon as the forward movement pedal is pushed the brush head motor and the suction motor will start
working, and as a result also the solenoid valve will start its work and detergent solution will be delivered
to the brush. During the first few metres, check that there is sufficient solution and that the squeegee is
drying correctly. The machine will now begin to work with full efficiency until the battery is flat or until the
detergent solution has finished.

37. BEGINNING TO WORK (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S -
Innova 70BTO versions)

To start working, do as follows:

9.
Make all the checks listed in “PREPARING TO WORK”.
10. Sit on the driver’s seat.
11. Turn the main switch key (01) clockwise by a quarter of a turn to "I". The control display on the
instrument panel will immediately comes on.

The first screen displayed indicates the name of the machine.
The second screen displayed (adjacent picture) indicates the characteristics of the machine's
programming.

The top part displays the settings for the type of batteries used.

The middle part of the display indicates the total time (first sequence of numbers) and the partial time
(second sequence of numbers) that the machine has been used. The numbers followed by the letter “h”
identify the hours, while the numbers followed by the letter “m” identify the tenths of an hour (a tenth of an
hour corresponds to six minutes).

WORK

Sayfa 39

The lower part of the screen displays the program release inserted into the circuit board.

The third screen (adjacent picture) displays the work panel. The symbols represent the following:

A.
Level of transfer or work speed.
B.
Level of the water in the machine's water system (versions with CDS).
C.
Level of the detergent in the machine's water system (versions with CDS).
D.
Battery charge level.

12. Choose the desired working program with the I-Drive device:

A.
Transfer: movement of the machine without working
B.
Drying: use the squeegee only
C.
Scrubbing / Drying: use both the brushes and the squeegee
D.
Scrubbing only : use brushes only

By selecting the "TRANSFER” program, the display screen will appear as in the adjacent figure. Both the
brush head and the squeegee are raised from the floor and are not operating.

By selecting the "DRYING” program, the display screen shown on the side will appear. The brush head is
raised from the floor and is not operating. The squeegee will position itself in contact with the floor as soon
as the forward movement pedal is pressed, in that moment the vacuum motor will start working.

ATTENTION: this program should only be used to collect the dirty solution after a
pre-wash, and should never be used for the work of vacuuming liquids.

If during the “DRYING” program the machine is stopped and the forward movement pedal is released, the
squeegee body will remain in contact with the floor for a few seconds, after which it will raise up from the
ground to go back to its rest position. For all these phases the suction motor will continue to operate, only
after a few seconds that it has returned to its work position will it switch off, this is to allow the motor to
collect all the liquid in the vacuum hose. During these phases, the symbol of the suction motor (02) on the
instrument panel display will blink, and it will only stop when the squeegee is in its work position and the
suction motor is off.

ATTENTION: by pressing the forward movement pedal it will start working with the
same program and with the same parameters that were set before it stopped.

ATTENTION: if reverse is carried out with this program active, the brush head unit
will raise up from the floor, the motor will keep working for a pre-set time and then it
will switch off.
ATTENTION: By pressing the forward movement pedal again, drying will start
working again normally.

WORK

Sayfa 40

By selecting the "SCRUBBING - DRYING” program, the display screen will appear as in the adjacent 
figure. Both the brush head and the squeegee will position themselves in contact with the floor as soon as 
the forward movement pedal is pressed, in that moment both the brush motor and the vacuum motor will 
start working. Also the solenoid valve will start to dispense detergent solution onto the brushes. 
 

 
 
 
If during the “SCRUBBING - DRYING” work the machine stops and the forward movement pedal is 
released, the brush motor and the solenoid valve will switch off, and after a few second the brush head 
unit will raise up off the ground and return to its rest position. The squeegee body will stay in contact with 
the floor for a few seconds, after which it will raise up from the ground and return to its rest position. For all 
these phases the suction motor will continue to operate, only after a few seconds that it has returned to its 
work position will it switch off, this is to allow the motor to collect all the liquid in the vacuum hose. During 
these phases, the symbol of the suction motor (02) on the instrument panel display will blink, and it will 
only stop when the squeegee is in its work position and the suction motor is off. 

ATTENTION: by pressing the forward movement pedal it will start working with the 
same program and with the same parameters that were set before it stopped. 

ATTENTION: if reverse is carried out with this program active, the brush head unit 
will raise up from the floor, the motor will keep working for a pre-set time and then it 
will switch off.  
ATTENTION: if reverse is carried out with this program active, the brush head body 
will remain in contact with the floor, the motor will continue working but the solenoid 
valve will no longer dispense any detergent solution onto the brushes. 
ATTENTION: By pressing the forward movement pedal again, drying will start 
working again normally. 

By selecting the "SCRUBBING” program, the display screen will appear as in the adjacent figure. The 
squeegee is raised from the floor and is not operating. The brush head will position itself in contact with 
the floor as soon as the forward movement pedal is pressed, in that moment the vacuum motor will start 
working. Also the solenoid valve will start to dispense detergent solution onto the brushes. 
 

 
 
 
If during the “SCRUBBING” work the machine stops and the forward movement pedal is released, the 
brush motor and the solenoid valve will switch off, and after a few second the brush head unit will raise up 
off the ground and return to its rest position. 

ATTENTION: by pressing the forward movement pedal it will start working with the 
same program and with the same parameters that were set before it stopped. 

13. Choose the forward operating speed by pushing the button (03) on the control panel. 
 

WORK 

02 

40

Sayfa 41

This machine has the possibility of selecting three different forward speeds, by pressing the button (03),
the passage from one to the other is continuous. The symbol (A) on the top left part of the control panel
display shows the speed.

ATTENTION: the reverse speed is lower than the forward speed to comply with
current health and safety standards.

14. If the machine does not have the CDS dosing device, move the knob (04) downwards and adjust the
amount of desired solution.
15. If the CDS dosing system is present, the knob (04) must be pulled completely down, thereby fully
opening the flow of water.

ATTENTION: with the CDS system, never operate the knob (04) when working. To
get a correct dosing of the detergent solution only use the buttons (05) and (06). See
paragraph “DETERGENT ADJUSTMENT WITH CDS SYSTEM”.

The level of the amount of water in the machine's water system is given by the symbol (B) in the lower left
part of the display.
The level of the percentage of detergent in the machine's water system is given by the symbol (C) in the
lower right part of the display.

16. Remove the parking brake, turn the lever (07) clockwise. The parking symbol “P” will disappear from
the control panel display.

ATTENTION: If you try to move forward with the parking brake engaged, the machine
will not move because the motor wheel is disengaged electrically when the parking
brake is active.

17. Pressing the forward movement pedal (08), the machine will start to move.

If the program selected is “SCRUBBING– DRYING” the squeegee and the brush head lower until they
touch the ground. As soon as the forward movement pedal is pushed the brush head motor and the
suction motor will start working, and as a result also the solenoid valve will start its work and detergent
solution will be dispensed onto the brushes. During the first few metres, check that there is sufficient
solution and that the squeegee is drying correctly. The machine will now begin to work with full efficiency
until the battery is flat or until the detergent solution has finished.

If there are any problems while you are working, press the emergency button (09) on the instrument
panel. This command interrupts the electrical circuit that goes from the batteries to the machine system.
After stopping and resolving the problem, resume the work by turning the key to “0”, setting the button (09)
to the standard position, and then turning the key to “I”.

WORK

Sayfa 42

38. DETERGENT REGULATION (VERSION WITHOUT CDS)

To regulate the amount of detergent solution on the brushes, proceed as follows:

1. Fully open the flow coming from the tap on the front of the machine by moving the knob (01) on the
rear of the steering column down.
2. Choose the desired working program with the I-Drive device, either "SCRUBBING - DRYING" or
"SCRUBBING".

3. By pressing the forward movement pedal (02) the brush head and the squeegee, or just the brush
head (depending on the program selected), will lower into a work position and the machine starts to
move. Both the brush motor and the suction motor (depending on the program selected) will start to
work and the solenoid valve will distribute detergent solution to the brushes.

In the first few metres, check that the quantity of solution is sufficient to wet the floor, but not so much that
it exits the splash guard, the amount of detergent can be adjusted by moving the knob (01),when lowering
it increases the flow onto the brushes, when raising it decreases the flow. Bear in mind that the correct
amount of solution always depends on the nature of the floor, the degree of dirt and the forward speed.

39. DETERGENT REGULATION (VERSION WITH CDS)

To regulate the amount of detergent solution on the brushes, proceed as follows:

1. Fully open the flow coming from the tap on the front of the machine by moving the knob on the rear of
the steering column down.
2. Choose the desired working program with the I-Drive device, either "SCRUBBING - DRYING" or
"SCRUBBING".

3. By pressing the button (01) for regulating the amount of water in the water circuit once, you can
display the level that has been set, in the centre of the display the symbol in question will appear with
the level highlighted (the symbol is shown in the picture on the side with the dispensing of water
finished).

4. By pressing the button (01) for regulating the amount of water in the water circuit once again, you can
change the level.

The quantity of water varies from a minimum of 40 litres/hour to a maximum of 140 litres/hour, with 7 set
dosage levels. the right water flow should be proportional to the degree of dirt on the floor. In addition,
remember that the time available for continuous working depends on the quantity of water in the tank.

5. By pressing the button (02) for regulating the percentage of detergent in the water circuit once, it is
possible to display the level that has been set, in the centre of the display the symbol in question will
appear with the level highlighted (the symbol is shown in the picture on the side with the dispensing of
detergent finished).

WORK

Sayfa 43

6. By pressing the button (02) for regulating the percentage of detergent in the water circuit once again,
you can change the percentage.

The percentage of detergent in the solution varies from a minimum of 0.5 % to a maximum of 3.5 % with 7
set dosing levels. The correct detergent flow should be proportional to the degree of dirt on the floor. In
addition, remember that the time available for continuous working depends on the quantity of detergent in
the canister.

To make it easier to set the parameters on the instrument panel (see adjacent picture) there is a table with
the values and the variation of the symbols, both for the water level as well as for the percentage of
detergent.

7. By pressing the forward movement pedal the brush head and the squeegee, or just the brush head
(depending on the program selected), will lower into a work position and the machine starts to move.
Both the brush motor and the suction motor (or only the brush head, depending on the program
selected) will start to work and the solenoid valve will distribute detergent solution to the brushes.

During the first few meters check that the amount of solution is sufficient to wet the floor, but not excessive
to exit the splash guard. Bear in mind that the correct amount of solution always depends on the nature of
the floor, the degree of dirt and the forward speed.

In case of failure of the CDS system, or if you want to work without this device, you use the lever (03) of
the tap mounted on the brush head near the motor. Press the buttons (01) and (02) until the levels of
water delivery and detergent percentage are zero.

By positioning the tap lever (03) in this way, the CDS dosing system is activated.

By positioning the tap lever (03) in this way, there will be no leakage of detergent solution on the brushes.
Press the buttons (01) and (02) until the levels of water delivery and detergent percentage are zero.

By positioning the tap lever in this way the CDS dosing system is excluded and the detergent solution is
deposited on the brushes. Press the buttons (01) and (02) until the levels of water delivery and detergent
percentage are zero.

ATTENTION: before regulating the solution, check there is detergent in the inner
canister, and that the water tap on the side is open.

ATTENTION: to resolve any malfunctioning of the CDS system, contact the
Assistance Centre.

WORK

Sayfa 44

40. ADJUSTING THE FORWARD WORKING SPEED (Innova 65B - Innova 75B - Innova 85B -
Innova 100B - Innova 70S - Innova 70BTO versions)

This machine allows you to choose from three different forward speeds using the button (01) on the
instrument panel. The selection is continuous cycle, by pressing the button you pass from one level to
another.

WARNING! the reverse speed is lower than the forward speed to comply with current
health and safety standards.

To display the speed level that has been set, just look at the symbol (02) on the display.

41. WATER MANAGEMENT KIT (Innova 60B versions)

If you want to increase the working capacity of the machine, you can replace the detergent solution choke
bushing on the solenoid valve (optional) with the more suitable one included in the water management kit.
To do this, proceed as follows:

1.
Take the machine to the designated maintenance place.
2.
Block the machine in place by engaging the parking brake, press the pedal (01) and block it with
the lever (02) at the rear of the steering column (read the section “PARKING BRAKE AND
SERVICE BRAKE”).

3.
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left.
4.
Remove the key from the instrument panel.

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of
serious injury to hands.

5.
Make sure that the brush head unit is in contact with the floor, if not, lower it by turning the lever
(04), positioned on the rear of the steering column, clockwise.

6.
Make sure the solution tank is empty. If this is not the case, empty it (read "EMPTYING THE
SOLUTION TANK").
7.
Check that the detergent solution regulation tap is closed, if not, close it by moving the knob (05) on
the back of the steering column up.

WORK

Sayfa 45

8.
Remove the plastic clamp that fixes the solution distribution tube to the solenoid valve
9.
Remove the solution distribution tube from the solenoid valve
10. If present, remove the solution choke bushing (06) and replace it with the more suitable one, or
insert the more suitable choke bushing at the required working capacity (the choke bushings are
included in the water management kit)
11. Reassemble all the elements

42. "ECO" DEVICE (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova
70BTO versions)

By activating “ECO MODE” mode using the relevant button (01) on the instrument panel, the energy used
by the machine is reduced, decreasing the power of the brushes motor and the suction motor. Just press
the button (01) on the instrument panel to deactivate the "ECO MODE" function.

If, when working in "DRYING" mode, the "ECO MODE" button is pressed, the control display will
immediately undergo the change (02) shown in the image on the side.

If, when working in "SCRUBBING - DRYING" mode, the "ECO MODE" button is pressed, the control
display will immediately undergo the change (03) shown in the image on the side.

If, when working in "SCRUBBING" mode, the "ECO MODE" button is pressed, the control display will
immediately undergo the change (04) shown in the image on the side.

43. EXTRA BRUSH HEAD BODY PRESSURE (Innova 65B - Innova 75B - Innova 85B versions)

This machine allows you to increase the pressure on the brushes using the pedal (01) on the front left of
the seat, and this can only be done when the brush head is in contact with the ground.

WARNING! The extra pressure should be engaged taking into account the type of floor
and the degree of dirt. An increase in pressure could cause greater wear and tear of the
brushes and greater energy consumption.

WORK

Sayfa 46

If, when working in "SCRUBBING - DRYING" mode, the extra pressure pedal is pressed, the control
display will immediately undergo the change (02) shown in the image on the side.

If, when working in "SCRUBBING" mode, the extra pressure pedal is pressed, the control display will
immediately undergo the change (03) shown in the image on the side.

If, when working in "SCRUBBING - DRYING" mode in "ECO MODE", the extra pressure pedal is pressed,
the control display will immediately undergo the change (04) shown in the image on the side.

If, when working in "SCRUBBING" mode in "ECO MODE", the extra pressure pedal is pressed, the control
display will immediately undergo the change (05) shown in the image on the side.

WARNING! If, while working with the extra pressure active, you stop and release the
forward movement pedal, the brush head will not raise up from the ground in order to
avoid seriously damaging the machine.

44. OVERFLOW DEVICE (Innova 60B versions)

The machine is NOT equipped with an overflow device, because the capacity of the recovery tank is
greater than the capacity of the solution tank. In extraordinary cases, there is a mechanical device (float)
under the recovery tank lid that, when the recovery tank is full, shuts off the air to the vacuum motor intake
to protect it; the sound of the suction motor will then be deeper.

If this is the case, proceed as follows:

1.
Raise the brush head off the ground, turn the lever (01) anti-clockwise. As soon as the brush head
reaches the rest position it will stop working.

WORK

Sayfa 47

2.
Raise the squeegee off the ground, turn the lever (02) clockwise.

3.
After about 15-25 seconds turn the key (03) 1/4 of a turn left, this will stop the machine.

4.
Turn the key (03) 1/4 of a turn right, this will start the machine.

ATTENTION: During machine switch-on, do not keep the accelerator pedal pressed
down.

5.
Bring the machine to the designated place for draining off the dirty water, and empty the recovery
tank (refer to “DRAINING THE RECOVERY TANK”).

WARNING! It is good practice every time the solution tank level is topped up, to empty
the recovery tank using the special drainage hose.

45. OVERFLOW DEVICE (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova 70S -
Innova 70BTO versions)

If this is the case, proceed as follows:

1.
Using the switch on the instrument panel select the “TRANSPORT” program (A), in this way the
brush motors and the solenoid valve will stop working, after a few seconds the brush head unit will
lift up from the floor. The squeegee will remain in contact with the floor for a few seconds, to allow
the drying to finish, after which it will lift up off the floor. A few seconds after the squeegee is in the
rest position the vacuum motor stops working, this is to allow all the liquid in the suction hose to be
suctioned off.

2.
Bring the machine to the designated place for draining off the dirty water, and empty the recovery
tank (refer to “DRAINING THE RECOVERY TANK”).

WARNING! It is good practice every time the solution tank level is topped up, to empty
the recovery tank using the special drainage hose.

WORK

Sayfa 48

 
 
At the end of the work, and before carrying out any type of maintenance, perform the following operations: 
 

1. 
Take the appliance to the dedicated dirty water drainage area. 
2. 
Bring the main machine switch to "0" by turning the key on the instrument panel a quarter rotation to 
the left. 
3. 
Engage the parking brake, rotating the lever on the rear of the steering column anti-clockwise. 

4. 
Empty the recovery tank (read the section “EMPTYING THE RECOVERY TANK”). 

5. 
Empty the solution tank (read the section “EMPTYING THE SOLUTION TANK”). The adjacent 
picture shows the drainage tube for the Innova 60-65-75-85-100 B versions. 

6. 
Remove the squeegee unit and clean it of any impurities (read the section “CLEANING THE 
SQUEEGEE UNIT”). 

7. 
Remove the brushes and eliminate the impurities on them (read “CLEANING THE DISC BRUSHES 
(Innova 65B - Innova 75B - Innova 85B - Innova 100B versions)” or “CLEANING THE DISC 
BRUSHES (Innova 60B versions)” or “CLEANING THE CYLINDRICAL BRUSH (Innova 70S 
versions)”). The adjacent image shows a disc brush for the Innova 65B - Innova 75B - Innova 85B 
versions. 

8. 
Remove the water system filter and clean it of any dirt (read the section “CLEANING THE WATER 
SYSTEM FILTER”). 

AT THE END OF THE WORK 

48

Sayfa 49

9. 
Remove the debris hopper and eliminate the impurities in it (read “CLEANING THE DEBRIS 
HOPPER (Innova 70S versions)”). 
 

 
 
 
10. Engage the parking brake, rotating the lever on the rear of the steering column clockwise. 
11. Bring the main machine switch to "I" by turning the key on the instrument panel a quarter rotation to 
the right. 
12. Take the machine to the designated machine storage place. 
 

ATTENTION: Park the machine in an enclosed place, on a flat surface; near the 
machine there must be no objects that could either damage it, or be damaged 
through contact with it. 

13. Bring the main machine switch to "0" by turning the key on the instrument panel a quarter rotation to 
the left. 
14. Remove the key from the controls instrument panel. 
15. Engage the parking brake, rotating the lever on the rear of the steering column anti-clockwise. 

16. Grip the handle on the right side of the recovery tank. 
17. Lift the recovery tank until it hooks to the end of the safety catch. 

18. Disconnect the electric system connector from the battery connector. 
 

ATTENTION: This process must be carried out by qualified personnel. An incorrect 
connection of the connector may cause a malfunction of the device. 

 
19. Grip the handle on the safety catch and lower the recovery tank until it is in the work position. 

ATTENTION: at the end of the job, you are advised to raise the cap (01) until the 
hook (02) is secured to the prop (03) of the recovery tank. 

AT THE END OF THE WORK 

49

Sayfa 50

PERFORM ALL MAINTENANCE OPERATIONS IN SEQUENCE
46. EMPTYING THE RECOVERY TANK

Proceed as follows to empty the recovery tank:

1.
Take the machine to the designated machine maintenance area; use the switch on the instrument
panel to select the “TRANSPORT” program (A).

2.
Block the machine in place by engaging the parking brake, press the pedal (01) and block it with
the lever (02) at the rear of the steering column (read the section “PARKING BRAKE AND
SERVICE BRAKE”).

3.
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left.
4.
Remove the key from the instrument panel.

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of
serious injury to hands.

5.
Remove the drainage tube of the recovery tank from the clamps, it is located at the rear of the
machine.

6.
Bend the end of the drainage tube, so as to create a choke and prevent the content from coming
out, put the tube on the discharge surface and gradually release the tube.
7.
Repeat the operations in reverse order to reassemble all the parts.

ATTENTION: The place this operation is carried out should comply with current
environmental protection regulations.

47. DRAINING THE SOLUTION TANK (Innova 65B - Innova 75B - Innova 85B - Innova 100B -
Innova 70BTO versions)

Proceed as follows to empty the recovery tank:

1.
Take the machine to the designated machine maintenance area; use the switch on the instrument
panel to select the “TRANSPORT” program (A).

DAILY MAINTENANCE

Sayfa 51

3.
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left.
4.
Remove the key from the instrument panel.

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of
serious injury to hands.

5.
Remove the drainage tube (04) of the solution tank from the clamps, it is located on the left side of
the machine.
6.
Put the tube on the drainage surface and unscrew the cap.

ATTENTION: The place this operation is carried out should comply with current
environmental protection regulations.

7.
Repeat the operations in reverse order to reassemble all the parts.

48. DRAINING THE SOLUTION TANK (Innova 70S versions)

Proceed as follows to empty the solution tank:

1.
Take the machine to the designated machine maintenance area; use the switch on the instrument
panel to select the “TRANSPORT” program (A).

3.
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left.
4.
Remove the key from the instrument panel.

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of
serious injury to hands.

DAILY MAINTENANCE

Sayfa 52

5.
Remove the drainage plug (04) of the solution tank, it is located on the left side of the machine.

ATTENTION: The place this operation is carried out should comply with current
environmental protection regulations.

6.
Repeat the operations in reverse order to reassemble all the parts.

49. CLEANING THE SQUEEGEE BODY

The careful cleaning of the whole vacuum unit ensures better drying and cleaning of the floor as well as a
longer suction motor life. To carry out the cleaning of the squeegee body, proceed as follows:

1.
Take the machine to the designated machine maintenance area; use the switch on the instrument
panel to select the “TRANSPORT” program (A).

3.
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left.
4.
Remove the key from the instrument panel.

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of
serious injury to hands.

5.
Remove the vacuum hose (04) from the vacuum nozzle (05) on the squeegee body.
6.
Loosen the knobs (06) in the squeegee body pre-assembly.

7.
Remove the squeegee body from the slits in the squeegee connector.
8.
First with a jet of water and then with a damp cloth, thoroughly clean the vacuum chamber (07) of
the squeegee unit.

ATTENTION: The place this operation is carried out should comply with current
environmental protection regulations.

DAILY MAINTENANCE

Sayfa 53

9.
First with a jet of water and then with a damp cloth, thoroughly clean the front rubber blade (08) of
the squeegee body.
10. Check the wear of the front rubber blade (08) on the squeegee body; if the edge of the rubber in
contact with the floor is worn, replace it. Refer to "REPLACING THE SQUEEGEE UNIT RUBBER
BLADES".

11. First with a jet of water and then with a damp cloth, thoroughly clean the rear rubber blade (09) of
the squeegee body.
12. Check the wear of the rear rubber blade (09) on the squeegee body; if the edge of the rubber in
contact with the floor is worn proceed with replacement, reading the paragraph "REPLACING THE
SQUEEGEE UNIT RUBBER BLADES" first, in any event it is possible to turn the rubber blade
around four edges.

13. Tighten the knobs (10) that fix the vacuum nozzle (05) to the squeegee body.
14. First with a jet of water and then with a damp cloth, thoroughly clean the vacuum nozzle (05). Also
clean the squeegee body support surface.
15. Position the vacuum nozzle (05) on the squeegee body and fix it in place by means of the knobs
(10).
16. Repeat the operations in the reverse order to reassemble everything

50. CLEANING THE DISC BRUSHES (Innova 60B versions)

Careful cleaning of the brushes guarantees better cleaning of the floor as well as a longer brush motor life.
To clean the brushes, proceed as follows:

1.
Take the machine to the designated maintenance place.

ATTENTION: The place this operation is carried out should comply with current
environmental protection regulations.

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of
serious injury to hands.

3.
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left.
4.
Remove the key from the instrument panel.

DAILY MAINTENANCE

Sayfa 54

5.
Check that the brush head unit is raised from the floor, if necessary turn the lever (04) anti-
clockwise. As soon as the brush head reaches the rest position it will stop working.

6.
Rotate the brush until it comes out of the housing of the brush-holder plate.
7.
Clean the brushes under a jet of water and remove any dirt in the brush bristles. Check the bristles.
If they are excessively worn, replace the brushes (the bristles should protrude by at least 10mm).
Read the section “REPLACING DISC BRUSHES (Innova 60 B version)” for replacing the brush.
8.
Repeat the operations in reverse order to reassemble all the parts.

51. CLEANING THE DISC BRUSHES (Innova 65B - Innova 75B - Innova 85B - Innova 100B
versions)

Careful cleaning of the brushes guarantees better cleaning of the floor as well as a longer brush motor life.
To clean the brushes, proceed as follows:

1.
Take the machine to the designated machine maintenance area; use the switch on the instrument
panel to select the “TRANSPORT” program (A).

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of
serious injury to hands.

3.
Press the brush uncoupling button (03) on the instrument panel. As soon as the button is pressed,
you will see the question “RELEASE?” on the screen. Press the brush release button (03) on the
steering wheel again, to confirm

ATTENTION: The place this operation is carried out should comply with current
environmental protection regulations.

4.
Clean the brushes under a jet of water and remove any dirt in the brush bristles. Check the bristles.
If they are excessively worn, replace the brushes (the bristles should protrude by at least 10mm). If
you need to replace the brushes, read “REPLACING THE DISC BRUSHES (Innova 65B - Innova
75B - Innova 85B - Innova 100B versions)”.
5.
Repeat the operations in reverse order to reassemble all the parts.

DAILY MAINTENANCE

Sayfa 55

you are advised to invert the right and left-hand brushes every day. If the brushes are not new however,
and have deformed bristles, it is better to reassemble them in the same position (the right-hand one on the
right, and the left-hand one on the left), to prevent the different inclination of the bristles producing an
overload on the brush motor as well as excessive vibrations.

52. CLEANING THE CYLINDRICAL BRUSH (Innova 70S versions)

Careful cleaning of the brush guarantees better cleaning of the floor as well as a longer brush motor life.
To clean the brush, proceed as follows:

1.
Take the machine to the designated machine maintenance area; use the switch on the instrument
panel to select the “TRANSPORT” program (A).

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of
serious injury to hands.

3.
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left.
4.
Remove the key from the instrument panel.

5.
With the brush head in a high position remove the right brush head casing (04), uncoupling the
retention hinges (05).

ATTENTION: The place this operation is carried out should comply with current
environmental protection regulations.

6.
Remove the brushes from the tunnel.
7.
Clean the brush under running water and remove any impurities present in the bristles of the brush.

Check the bristles. If they are excessively worn, replace the brushes (the bristles should protrude by at
least 10mm). If you need to replace the brush, read “REPLACING THE CYLINDRICAL BRUSH (Innova
70S version)”.

DAILY MAINTENANCE

Sayfa 56

8.
Clean the splash guard rubber on the left side of the brush head unit well with a wet cloth and on
the right casing.
9.
Repeat the operations in reverse order to reassemble all the parts.

ATTENTION: The brush must have the cusp facing towards the front of the machine to
be fitted in the correct manner.

53. CLEANING THE DEBRIS HOPPER (Innova 70S versions)

Careful cleaning of the debris hopper guarantees better cleaning of the floor as well as a longer suction
motor life. To clean the debris hopper, proceed as follows:

1.
Take the machine to the designated machine maintenance area; use the switch on the instrument
panel to select the “TRANSPORT” program (A).

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of
serious injury to hands.

3.
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left.
4.
Remove the key from the instrument panel.

5.
Disconnect the hopper vacuum hose (04).
6.
Turn the knob (05) anti-clockwise until the debris hopper is free to move.
7.
Using the flush handle (06), remove the hopper and empty it.

ATTENTION: The place this operation is carried out should comply with current
environmental protection regulations.

8.
Check the wear of the rubber (07) and clean it with a jet of running water and then with a damp
cloth.
9.
Turn the hopper vacuum filter (08) anti-clockwise, pulling it towards the vacuum hose and extract it
from the retainer pin.
10. Clean underneath with a jet of water and check it is working correctly.
11. Repeat the operations in reverse order to reassemble all the parts.

DAILY MAINTENANCE

Sayfa 57

54. CLEANING THE RECOVERY TANK FILTER 

Careful cleaning of the recovery tank filter guarantees better cleaning of the floor as well as a longer 
suction motor life. Proceed as follows to clean the recovery tank filter: 

1. 
Take the machine to the designated machine maintenance area; use the switch on the instrument 
panel to select the “TRANSPORT” program (A). 

2. 
Block the machine in place by engaging the parking brake, press the pedal (01) and block it with 
the lever (02) at the rear of the steering column (read the section “PARKING BRAKE AND 
SERVICE BRAKE”). 
 

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of 
serious injury to hands. 

3. 
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left. 
4. 
Remove the key from the instrument panel. 

5. 
Raise the cap (04) until the hook (05) is secured to the prop (06) of the recovery tank. 

6. 
Remove the vacuum filter protection (07) by rotating it in a clockwise direction. 
7. 
Release the retaining clips (08). 
 

 
 
 
8. 
Take the vacuum filter out of the housing (09), clean the walls and the bottom of the filter with a jet 
of water, remove any dirt that is attached. 
9. 
Repeat the operations in reverse order to reassemble all the parts. 
 

ATTENTION: The place this operation is carried out should comply with current 
environmental protection regulations. 

DAILY MAINTENANCE 

57

Sayfa 58

55. CLEANING THE RECOVERY TANK

The careful cleaning of the recovery tank guarantees a longer machine life. Proceed as follows to clean
the recovery tank:

1.
Take the machine to the designated machine maintenance area; use the switch on the instrument
panel to select the “TRANSPORT” program (A).

3.
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left.
4.
Remove the key from the instrument panel.

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of
serious injury to hands.

5.
Release the recovery tank drainage tube (at the back of the machine) from the retainers. Remove
the cap and place it on the ground.
6.
Grip the handle on the right side of the recovery tank.
7.
Lift the recovery tank until it hooks to the safety clamp at the first point.

8.
Raise the cap (04) until the hook (05) is secured to the prop (06) of the recovery tank.
9.
Rinse the inside with a jet of water, if necessary use a spatula to remove the sludge that has
accumulated at the bottom of the tank.
10. Repeat the operations in reverse order to reassemble all the parts.

ATTENTION: The place this operation is carried out should comply with current
environmental protection regulations.

56. CLEANING THE SOLUTION TANK (Innova 65B – Innova 75B – Innova 85B – Innova 100B –
Innova 70BTO versions)

The careful cleaning of the solution tank guarantees a longer machine life. Proceed as follows to clean the
solution tank:

1.
Take the machine to the designated machine maintenance area; use the switch on the instrument
panel to select the “TRANSPORT” program (A).

WEEKLY MAINTENANCE

Sayfa 59

2. 
Block the machine in place by engaging the parking brake, press the pedal (01) and block it with 
the lever (02) at the rear of the steering column (read the section “PARKING BRAKE AND 
SERVICE BRAKE”). 

3. 
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left. 
4. 
Remove the key from the instrument panel. 
 

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of 
serious injury to hands. 

5. 
Remove the drainage tube (04) of the solution tank from the clamps, it is located on the left side of 
the machine, unscrew the cap and lay it on the ground. 

6. 
Remove the filling cap (05) and the filter (06) on the left side of the machine. Clean the filter (06) 
with a jet of water and remove any dirt. 

 
 
 
7. 
Clean the inside of the solution tank with a jet of water. 
8. 
Repeat the operations in reverse order to reassemble all the parts. 
 

ATTENTION: The place this operation is carried out should comply with current 
environmental protection regulations. 

57. CLEANING THE SOLUTION TANK (Innova 70S versions) 

The careful cleaning of the solution tank guarantees a longer machine life. Proceed as follows to clean the 
solution tank: 

1. 
Take the machine to the designated machine maintenance area; use the switch on the instrument 
panel to select the “TRANSPORT” program (A). 

WEEKLY MAINTENANCE 

59

Sayfa 60

2. 
Block the machine in place by engaging the parking brake, press the pedal (01) and block it with 
the lever (02) at the rear of the steering column (read the section “PARKING BRAKE AND 
SERVICE BRAKE”). 

3. 
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left. 
4. 
Remove the key from the instrument panel. 
 

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of 
serious injury to hands. 

5. 
Unscrew the drainage plug (04) of the solution tank, it is located on the left side of the machine. 

6. 
Remove the filling cap (05) and the filter (06) on the left side of the machine. Clean the filter (06) 
with a jet of water and remove any dirt. 

 
 
 
7. 
Clean the inside of the solution tank with a jet of water. 
8. 
Repeat the operations in reverse order to reassemble all the parts. 
 

ATTENTION: The place this operation is carried out should comply with current 
environmental protection regulations. 

58. CLEANING THE WATER SYSTEM FILTER 

The careful cleaning of the water system guarantees a better cleaning of the floor as well as a longer life 
for all the components that make up the water system. To clean the water system filter, proceed as 
follows: 

1. 
Take the machine to the designated machine maintenance area; use the switch on the instrument 
panel to select the “TRANSPORT” program (A). 

WEEKLY MAINTENANCE 

60

Sayfa 61

3.
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left.
4.
Remove the key from the instrument panel.
5.
Make sure the solution tank is empty. If it isn't, empty it completely.

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of
serious injury to hands.

6.
Unscrew the filter cap (04) of the water system on the front of the machine.
7.
Remove the filter cartridge (05) and clean it under a jet of water, remove any dirt that might be
attached.
8.
Repeat the operations in reverse order to reassemble all the parts.

ATTENTION: The place this operation is carried out should comply with current
environmental protection regulations.

59. CLEANING THE VACUUM TUBE (Innova 65B - Innova 75B - Innova 85B - Innova 100B -
Innova 70BTO versions)

Careful cleaning of the vacuum hose guarantees better cleaning of the floor as well as a longer suction
motor life. Proceed as follows to clean the vacuum hose:

1.
Take the machine to the designated machine maintenance area; use the switch on the instrument
panel to select the “TRANSPORT” program (A).

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of
serious injury to hands.

3.
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left.
4.
Remove the key from the instrument panel.

WEEKLY MAINTENANCE

Sayfa 62

5. 
Remove the vacuum hose (04) from the vacuum nozzle (05) on the squeegee body. 

6. 
Grip the handle on the right side of the recovery tank. 
7. 
Lift the recovery tank until it hooks to the end of the safety catch. 

8. 
Remove the vacuum hose (06) from the recovery tank. 
9. 
Clean the inside with a jet of water, inserting the tube in the part of the vacuum nozzle that was 
fixed to the recovery tank. 
10. Repeat the operations in reverse order to reassemble all the parts. 
 

ATTENTION: The place this operation is carried out should comply with current 
environmental protection regulations. 

60. CLEANING THE VACUUM TUBE (Innova 70S versions) 

Careful cleaning of the vacuum hose guarantees better cleaning of the floor as well as a longer suction 
motor life. Proceed as follows to clean the vacuum hose: 

1. 
Take the machine to the designated machine maintenance area; use the switch on the instrument 
panel to select the “TRANSPORT” program (A). 

2. 
Block the machine in place by engaging the parking brake, press the pedal (01) and block it with 
the lever (02) at the rear of the steering column (read the section “PARKING BRAKE AND 
SERVICE BRAKE”). 
 

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of 
serious injury to hands. 

3. 
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left. 
4. 
Remove the key from the instrument panel. 

WEEKLY MAINTENANCE 

62

Sayfa 63

5. 
Remove the vacuum hose (04) from the vacuum nozzle (05) on the squeegee body. 

6. 
Remove the debris hopper vacuum hose (06) from the vacuum nozzle (07) on the brush head unit. 

7. 
Grip the handle on the right side of the recovery tank. 
8. 
Lift the recovery tank until it hooks to the end of the safety catch. 

9. 
Remove the vacuum hose (08) from the recovery tank. 
10. Clean the inside with a jet of water, inserting the tube in the part of the vacuum nozzle that was 
fixed to the recovery tank. 
11. Repeat the operations in reverse order to reassemble all the parts. 
 

ATTENTION: The place this operation is carried out should comply with current 
environmental protection regulations. 

61. CLEANING THE DETERGENT CANISTER (versions with CDS) 

Careful cleaning of the vacuum hose guarantees better cleaning of the floor as well as a longer suction 
motor life. Proceed as follows to clean the vacuum hose: 

1. 
Take the machine to the designated machine maintenance area; use the switch on the instrument 
panel to select the “TRANSPORT” program (A). 

2. 
Block the machine in place by engaging the parking brake, press the pedal (01) and block it with 
the lever (02) at the rear of the steering column (read the section “PARKING BRAKE AND 
SERVICE BRAKE”). 
 
 

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of 
serious injury to hands. 

WEEKLY MAINTENANCE 

63

Sayfa 64

3. 
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left. 
4. 
Remove the key from the instrument panel. 

5. 
Open the hatch (04) on the front of the steering column. 
 
 

6. 
Remove the cap (05) of the detergent canister (06). 
 
 

7. 
Remove the machine's detergent canister (06). 
8. 
Remove any detergent residue. 
9. 
Rinse the inside of the canister with a jet of running water. 
10. Repeat the operations in reverse order to reassemble all the parts. 
 

ATTENTION: The place this operation is carried out should comply with current 
environmental protection regulations. 

ATTENTION: Do not throw the detergent directly into the drain, but comply with current 
environmental protection regulations. 

WEEKLY MAINTENANCE 

64

Sayfa 65

62. REPLACING THE SQUEEGEE RUBBER BLADES (Innova 60B versions) 

Careful cleaning of the squeegee rubber guarantees better cleaning of the floor as well as a longer suction 
motor life. To replace the squeegee rubber blades, proceed as follows: 

1. 
Take the machine to the designated maintenance place. 

2. 
Block the machine in place by engaging the parking brake, press the pedal (01) and block it with 
the lever (02) at the rear of the steering column (read the section “PARKING BRAKE AND 
SERVICE BRAKE”). 

3. 
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left. 
4. 
Remove the key from the instrument panel. 

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of 
serious injury to hands. 

5. 
Check that the squeegee is raised from the floor, if not, turn the lever (04) clockwise. 

6. 
Remove the vacuum hose (04) from the vacuum nozzle (05) on the squeegee body. 
7. 
Loosen the knobs (06) in the squeegee body pre-assembly. 
8. 
Remove the squeegee body from the slits in the squeegee connector. 
 

Proceed as follows for replacing the front rubber blade of the squeegee body: 

1. 
Turn the wing nuts (07) in the horizontal position. 
2. 
Remove the front rubber-pressing blades (08). 
3. 
Remove the rubber (09) and replace it. 
4. 
Proceed in reverse to replace the rubber. 

EXTRAORDINARY MAINTENANCE 

65

Sayfa 66

Proceed as follows for replacing the rear rubber blade of the squeegee body: 

1. Turn the wing nuts (10) in the horizontal position. 
2. Remove the front rubber-pressing blades (11). 
3. Remove the rubber (12) and replace it. 
4. Proceed in reverse to replace the rubber. 

63. REPLACING THE SQUEEGEE RUBBER BLADES (Innova 65B - Innova 75B - Innova 85B - 
Innova 100B - Innova 70BTO versions) 

Careful cleaning of the squeegee rubber guarantees better cleaning of the floor as well as a longer suction 
motor life. To replace the squeegee rubber blades, proceed as follows: 

1. 
Take the machine to the designated machine maintenance area; use the switch on the instrument 
panel to select the “TRANSPORT” program (A). 

2. 
Block the machine in place by engaging the parking brake, press the pedal (01) and block it with 
the lever (02) at the rear of the steering column (read the section “PARKING BRAKE AND 
SERVICE BRAKE”). 

3. 
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left. 
4. 
Remove the key from the instrument panel. 

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of 
serious injury to hands. 

5. 
Remove the vacuum hose (04) from the vacuum nozzle (05) on the squeegee body. 
6. 
Loosen the knobs (06) in the squeegee body pre-assembly. 
7. 
Remove the squeegee body from the slits in the squeegee connector. 
 

Proceed as follows for replacing the front rubber blade of the squeegee body: 

1. 
Turn the wing nuts (07) in the horizontal position. 
2. 
Remove the front rubber-pressing blades (08). 
3. 
Remove the rubber (09) and replace it. 
4. 
Proceed in reverse to replace the rubber. 

EXTRAORDINARY MAINTENANCE 

66

Sayfa 67

Proceed as follows for replacing the rear rubber blade of the squeegee body: 

1. 
Turn the wing nuts (10) in the horizontal position. 
2. 
Remove the front rubber-pressing blades (11). 
3. 
Remove the rubber (12) and replace it. 
4. 
Proceed in reverse to replace the rubber. 

64. ADJUSTING THE SQUEEGEE (Innova 60B versions) 

Careful adjustment of the height between the squeegee rubber and the floor guarantees better drying and 
cleaning of the floor as well as a longer suction motor life. To regulate the squeegee rubber proceed as 
follows: 

1. 
Bring the brush head unit into contact with the floor, turn the lever (01) on the rear of the steering 
column clockwise. 

2. 
Bring the squeegee into contact with the floor, turn the lever (02) on the rear of the steering column 
anti-clockwise. 

3. 
Remove the parking brake, turn the lever (03) clockwise. In the control panel the red indicator light 
pertaining to the parking symbol “P” will go out. 
 

ATTENTION: If you try to move forward with the parking brake engaged, the machine 
will not move because the motor wheel is disengaged electrically when the parking 
brake is active. 

4. 
Adjust the flow of detergent coming out by using the knob (04) on the rear of the steering column. 

5. 
By pressing the forward movement pedal (05), the brushes and the suction motor start and the 
machine starts to move. 

EXTRAORDINARY MAINTENANCE 

67

Sayfa 68

If you need to increase the inclination of the rubber blade in the centre, it is necessary to tighten the screw
(06); to decrease it, just turn the screw (06) in the opposite direction.
During working operation, the rear rubber blade should be slightly tilted backwards by about 30°- 45° with
respect to the floor in a uniform way along its whole length. This means that the height of the squeegee
must be regulated, and this is done by turning the knob (07) (the diagram shows only the right-hand knob,
but there will be another one on the left-hand side) anti-clockwise to raise the squeegee and in the
opposite direction to lower it.

65. ADJUSTING THE SQUEEGEE (Innova 65B - Innova 75B - Innova 85B - Innova 100B - Innova
70S - Innova 70BTO versions)

Careful adjustment of the height between the squeegee rubber and the floor guarantees better drying and
cleaning of the floor as well as a longer suction motor life. To regulate the squeegee rubber proceed as
follows:

1.
Using the switch on the instrument panel, select the program “SCRUBBING - DRYING" (C).

2.
Remove the parking brake, turn the lever (01) clockwise. The parking symbol “P” will disappear
from the control panel display.

ATTENTION: If you try to move forward with the parking brake engaged, the machine
will not move because the motor wheel is disengaged electrically when the parking
brake is active.

3.
Adjust the flow of detergent coming out by using the knob (01) on the rear of the steering column.

4.
By pressing the forward movement pedal (02) the brushes and the suction motor start and the
machine starts to move.

If you need to increase the inclination of the rubber blade in the centre, it is necessary to tighten the screw
(03), while to decrease it just turn the screw (03) in the opposite direction. During working operation, the
rear rubber blade should be slightly tilted backwards by about 30°- 45° with respect to the floor in a
uniform way along its whole length. This means that the height of the squeegee should be regulated, and
this is done by turning the knob (04) (in the diagram only the right knob is depicted) anti-clockwise to raise
the squeegee and in the opposite direction to lower it.

ATTENTION: the right and left wheels must be adjusted to the same level, so the
squeegee can work parallel to the floor.

EXTRAORDINARY MAINTENANCE

Sayfa 69

66. REPLACING THE DISC BRUSH (Innova 60B versions)

Brushes in a good condition guarantee better cleaning of the floor as well as a longer brush motor life. To
replace the brush, proceed as follows:

1.
Take the machine to the designated maintenance place.

ATTENTION: The place this operation is carried out should comply with current
environmental protection regulations.

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of
serious injury to hands.

3.
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left.
4.
Remove the key from the instrument panel.

5.
Check that the brush head unit is raised from the floor, if necessary turn the lever (04) anti-
clockwise. As soon as the brush head reaches the rest position it will stop working.

6.
Rotate the brush until it comes out of the housing of the brush-holder plate.
7.
Replace the old brush with the new one

67. REPLACING THE DISC BRUSHES (Innova 65B - Innova 75B - Innova 85B - Innova 100B
versions)

Brushes in a good condition guarantee better cleaning of the floor as well as a longer brush motor life. To
replace the brushes, proceed as follows:

1.
Take the machine to the designated machine maintenance area; use the switch on the instrument
panel to select the “TRANSPORT” program (A).

EXTRAORDINARY MAINTENANCE

Sayfa 70

2. 
Block the machine in place by engaging the parking brake, press the pedal (01) and block it with 
the lever (02) at the rear of the steering column (read the section “PARKING BRAKE AND 
SERVICE BRAKE”). 

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of 
serious injury to hands. 

3. 
Press the brush uncoupling button (03) on the instrument panel. As soon as the button is pressed, 
you will see the question “RELEASE?” on the screen. Press the brush release button (03) on the 
steering wheel again, to confirm. 

4. 
Replace the old brush with the new one. 
 

68. REPLACING THE CYLINDRICAL BRUSH (Innova 70S versions) 

Brushes in a good condition guarantee better cleaning of the floor as well as a longer brush motor life. To 
replace the brush, proceed as follows: 

1. 
Take the machine to the designated machine maintenance area; use the switch on the instrument 
panel to select the “TRANSPORT” program (A). 

2. 
Block the machine in place by engaging the parking brake, press the pedal (01) and block it with 
the lever (02) at the rear of the steering column (read the section “PARKING BRAKE AND 
SERVICE BRAKE”). 
 

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of 
serious injury to hands. 

3. 
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left. 
4. 
Remove the key from the instrument panel. 

EXTRAORDINARY MAINTENANCE 

70

Sayfa 71

5.
With the brush head in a high position remove the right brush head casing (04), uncoupling the
retention hinges (05).

6.
Remove the brush to be replaced from the tunnel.
7.
Insert the brush (the side with 5 teeth) in the tunnel until it couples with the drive hub on the
opposite side of the tunnel.

ATTENTION: Pay attention to the direction of the brush bristles during assembly, the
cusp of the brush viewed from the above should be towards the front of the machine.

8.
Insert the idler wheel of the right brush head casing in the brush.
9.
Secure the right casing (04) to the brush head using the retention hinges (05).
10. Clean the splash guard rubber on the left side of the brush head unit well with a wet cloth and on
the right casing.
11. Repeat the operations in reverse order to reassemble all the parts.

Check the state of wear of the side splash guard blades and in the event of excessive wear replace the
splash guard blades. Read the section “REPLACING THE SIDE SPLASH GUARD BLADE (Innova70 S
version)” for replacing the rubber blade.

69. REPLACING THE BRUSH HEAD CARTER (Innova 65B - Innova 75B - Innova 85B - Innova
100B versions)

When the brush head casing is in a good condition it guarantees a better cleaning of the floor as well as a
longer brush motor life. To replace the brush, proceed as follows:

1. Take the machine to the designated machine maintenance area; use the switch on the instrument
panel to select the “TRANSPORT” program (A).

2. Block the machine in place by engaging the parking brake, press the pedal (01) and block it with the
lever (02) at the rear of the steering column (read the section “PARKING BRAKE AND SERVICE
BRAKE”).

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of
serious injury to hands.

3. Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left.
4. Remove the key from the instrument panel.

ATTENTION: This operation must be carried out by qualified personnel, using suitable
equipment. An incorrect connection may cause the machine to malfunction.

EXTRAORDINARY MAINTENANCE

Sayfa 72

7. Remove the casing to be replaced (04) from the brush head unit, the casing is fixed to it by means of 
screws (05). The image on the side shows the left casing. 
8. Secure the new casing to the brush head unit (read the section "ASSEMBLING THE BRUSH HEAD 
CASING"). 
9. Repeat the operation also for the casing on the opposite side.  
 
 

70. CLEANING THE DOSING SYSTEM (VERSIONS WITH CDS) 

If the machine is unused for long periods (more than 48 hours) it is recommended that the dosing system 
be washed, and to do this proceed as follows: 
 

1. 
Take the machine to the designated maintenance place. For the Innova 65-75-85-100 B versions 
and the Innova70 S versions, using the switch on the instrument panel select the program 
"TRANSPORT” (A). 

2. 
Block the machine in place by engaging the parking brake, press the pedal (01) and block it with 
the lever (02) at the rear of the steering column (read the section “PARKING BRAKE AND 
SERVICE BRAKE”). 
 

ATTENTION: users are advised to always wear protective gloves, to avoid the risk of 
serious injury to hands. 

3. 
Turn the main machine switch to "0" by turning the key (03) a quarter rotation to the left. 
4. 
Remove the key from the instrument panel. 
 
 

5. 
Verify that the bypass tap (04) is in the "dosing system" position, if not, position it as in the diagram. 
 

 
 
 
6. 
Make sure the solution tank is full, if not,fill it up (read the section "FILLING THE SOLUTION TANK 
WITH WATER"). 
7. 
Make sure the recovery tank is empty, otherwise empty it completely (read the section "EMPTYING 
THE RECOVERY TANK"). 
 

EXTRAORDINARY MAINTENANCE 

72

Sayfa 73

8. 
Open the hatch (05) on the front of the steering column. 

9. 
Unscrew the cap (06) of the detergent canister (07). 

 
 
 
10. Remove the machine's detergent canister (07). 
11. Fill the canister with clean water. 
 

ATTENTION: Fill with clean water, at a temperature not higher than 50C and not lower 
than 10°C. 

12. Put back the detergent canister (07). 
13. Screw on the cap (06) of the detergent canister (07), making sure that the detergent draft filter is 
correctly positioned on the bottom of the canister. 

14. Close the hatch (05) on the front of the steering column. 
15. Engage the parking brake, rotating the lever on the rear of the steering column clockwise. 

16. Using the switch on the instrument panel, select the program “SCRUBBING - DRYING" (C). 

EXTRAORDINARY MAINTENANCE 

73

Sayfa 74

17. Turn the main machine switch to "I", turn the key (03) a quarter rotation to the right. 
18. When the work screen appears on the control display, press the button (08). 

19. Set the maximum amount of water in the detergent solution, by pressing the button (08) until the 
symbol shown on the side is completely full. 

20. After regulating the amount of water in the detergent solution, press the button (09). 

21. Set the maximum amount of chemical in the detergent solution, by pressing the button (09) until the 
symbol shown on the side is completely full. 

22. Remove the parking brake, by turning the lever (02) on the rear of the steering column to the right 
(read the section “PARKING BRAKE AND SERVICE BRAKE”). 

23. Press the accelerator pedal (10) gently to activate the brush head and the dosing system. 
 

EXTRAORDINARY MAINTENANCE 

74

Sayfa 75

 
 
24. Wait a few minutes, normally 2 – 4 minutes, to allow the dosing system to be washed. 
25. Completely empty the solution tank and detergent canister. 
 

ATTENTION: The machine will dispense solution during this operation 

26. Using the switch on the instrument panel, select the program “TRANSPORT" (A). 
27. Take the machine to the designated machine storage place. 
 

ATTENTION: Park the machine in an enclosed place, on a flat surface; near the 
machine there must be no objects that could either damage it, or be damaged 
through contact with it. 

28. Bring the main machine switch to "0" by turning the key (03) on the instrument panel a quarter 
rotation to the left. 
29. Remove the key (03) from the control panel. 

30. Block the machine in place by engaging the parking brake, press the pedal (01) and block it with 
the lever (02) at the rear of the steering column (read the section “PARKING BRAKE AND 
SERVICE BRAKE”). 

31. Grip the handle on the right side of the recovery tank. 
32. Lift the recovery tank until it hooks to the end of the safety catch. 

33. Disconnect the electric system connector from the battery connector. 
 

ATTENTION: This process must be carried out by qualified personnel. An incorrect 
connection of the connector may cause a malfunction of the device. 

34. Grip the handle on the safety catch and lower the recovery tank until it is in the work position. 

EXTRAORDINARY MAINTENANCE 

75

Sayfa 76

71. INSUFFICIENT WATER ON THE BRUSHES

1.
Check that there is water in the solution tank, the amount inside the tank can be seen by means
of the level tube (01) on the front left of the seat.
2.
Make sure that the detergent solution tap is open, and check that the knob (02) on the back of the
steering column is completely lowered.

3.
Check that the water flow in the water system is not at zero, and with the machine on press the
button (03) once to view the delivery level. (versions with CDS)
4.
Check that the detergent flow in the water system is not at zero, and with the machine on press
the button (04) once to view the delivery level. (versions with CDS)

5.
Clean the solution filter located at the front of the machine.
6.
Make sure the water distribution pipe (05) (S versions) is not blocked.
7.
For the Innova 60B versions with “KIT WATER MANAGEMENT”, check that the choke bushing is
not blocked.

72. THE SQUEEGEE DOES NOT DRY PERFECTLY

1.
Check the squeegee is clean.
2.
Check the squeegee adjustments (read the section “SQUEEGEE ADJUSTMENT”).
3.
Clean the whole vacuum unit (read the relevant sections in the chapters “DAILY MAINTENANCE”
and “WEEKLY MAINTENANCE”).
4.
Replace the rubber blades if worn out (read the section “REPLACING THE SQUEEGEE
RUBBER BLADES).
5.
Check that the cap on the recovery tank drainage hose is properly closed.

73. THE MACHINE DOES NOT CLEAN WELL

1.
Check the state of wear and tear of the brushes and, if necessary, replace them. The brushes
should be changed when the bristles are about 15 mm long. To do this, read “REPLACING THE
DISC BRUSH” for Innova 65-75-85-100 B versions, or “REPLACING THE CYLINDRICAL
BRUSH” for the Innova 70S version. Working with over-worn brushes may cause damage to the
floor.
2.
Use a different kind of brush to the one fitted as standard. For cleaning floors where the dirt is
particularly resistant, we recommend the use of special brushes supplied upon request and
according to needs (see “CHOOSING AND USING THE BRUSHES”).

74. EXCESSIVE FOAM PRODUCTION

Check that a low foam detergent has been used. If necessary, add a small quantity of anti-foam liquid to
the recovery tank.
Remember that, when the floor is not very dirty, more foam is generated. In this case the detergent
solution should be more diluted.

75. THE VACUUM CLEANER DOES NOT FUNCTION

1.
Check whether the recovery tank is full and, if necessary, empty it.
2.
Check the float on the vacuum cap is working properly (see also “CLEANING THE RECOVERY
TANK” and “CLEANING THE RECOVERY TANK FILTER”).

TROUBLESHOOTING

Sayfa 77

76. THE BRUSH MOTOR DOESN'T WORK (INNOVA 60B VERSIONS)

ATTENTION To avoid damaging the floor, the engine only starts up when the machine is moved
forwards

1.
Check that the brush head is lowered during the forward movement, with the right lever (01)
turned clockwise.
2.
The operator must be properly seated in the driving position
3.
Check no thermal protection device has intervened.
4.
Check the correct connection of the engine to the terminal board under the footboards.

77. THE BRUSH MOTOR DOES NOT WORK

ATTENTION To avoid damaging the floor, the motor only starts up when the machine is moved
forwards.

1.
Check that the brush head is lowered during start-up.
2.
The operator must be properly seated in the driving position.
3.
Check the I-DRIVE selector is on “C” or “D” (brush operating function) (valid only for Innova 65B -
Innova 75B - Innova 85B - Innova 100B - Innova 70S - Innova 70BTO versions).
4.
Check no thermal protection device has intervened.
5.
Check the correct connection of the engine to the terminal board under the footboards.

78. IT IS IMPOSSIBLE TO RAISE OR LOWER THE BRUSH HEAD OR SQUEEGEE

The machine is fitted with electrical protection devices that control the brush head and squeegee
ascent/descent motor reducers. In the event of overloading, the fuses interrupt the power supply. After
checking and removing the reason for the problem, to reset them just switch the machine off then on
again. If the problem persists, contact the specialist technical assistance centre.

79. THE MACHINE DOES NOT START

1.
Check the connector is connected to the batteries.

2.
Check the key switch (01) is on "I".

3.
Check that the batteries are charged, control the symbol (02) on the control display.

TROUBLESHOOTING

Sayfa 78

80. ELECTRIC FUSES AND THERMAL CUT-OUTS 

In addition to general 80 A fuses, the machine is also fitted with self-restoring safety fuses located on 
the boards in the electric system that interrupt the power supply to the brush and suction motor when 
the machine exceeds the predetermined load. To restore the power supply to the motor, switch off the 
machine and wait for the fuses to cool down (about 40 seconds). If the switch disconnects the current 
several times in a row, contact the specialised technical assistance centre. 

81. THE AUTOMATIC WATER/DETERGENT DOSING SYSTEM DOES NOT WORK 

The automatic water/detergent dosing system has been designed with criteria of extreme sturdiness and 
reliability, but there is a special by-pass system that allows you to use the machine even if the system is 
out-of-use. 
To by-pass the automatic water/detergent dosing system, you must rotate the tap lever (01) on the rear-
centre of the base downwards; in this way you can go on working even with the system out-of-use. 
Remember, however, to put not only water in the solution tank, but the right quantities of both water and 
detergent. With the dosing system out-of-use, the water flow is regulated via the tap on the steering 
column. 
Contact an Authorised Retailer to have the system repaired. 

TROUBLESHOOTING 

78

Sayfa 79

 
To dispose of the machine, take it to a demolition centre or an authorised collection centre. 
 
Before scrapping the machine, it is necessary to remove and separate out the following materials, then 
send them to the appropriate collection centres in accordance with the environmental hygiene 
regulations currently in force: 

• Brushes 
• Felt 
• Electric and electronic parts* 
• Batteries 
• Plastic parts (tanks and handlebars) 
• Metal parts (levers and frame) 
 
(*) In particular, contact your local distributor when scrapping electric and electronic parts. 
 

DISPOSAL 

79

Sayfa 80

POLYPROPYLENE BRUSH (PPL)
Used on all types of floors. Good resistance to wear and tear, and hot water (no greater than 60°C.). PPL is non-hygroscopic and therefore retains its
characteristics even when working in wet conditions.

NYLON BRUSH
Used on all types of floors. Excellent resistance to wear and tear, and hot water (even over 60°C). The nylon is hygroscopic and so tends to lose its
characteristics over time when working in wet conditions.

ABRASIVE BRUSH
The bristles of this type of brush are charged with highly aggressive abrasives. It is used to clean very dirty floors. To avoid floor damage, work only with the
pressure strictly necessary.

BRISTLE THICKNESS
Thicker bristles are more rigid and are therefore used on smooth floors or floors with small joints.
On uneven floors or those with deep joints, it is advisable to use softer bristles which can enter the gaps more easily.
Remember that when the bristles are worn and therefore too short, they will become rigid and are no longer able to penetrate and clean deep down. In this
case, like with over-large bristles, the brush tends to jump.

PAD HOLDER
The pad holder is recommended for cleaning shiny surfaces.
There are two types of pad holder:

1.
The traditional pad holder is fitted with a series of anchor points that allow the abrasive floor pad to be held and dragged while working.
2.
The CENTRE LOCK type pad-holder not only has anchor points, but also a snap-type central locking system in plastic that allows the abrasive disc to
be perfectly centred and held without any risk of it becoming detached. This type of holder is especially suitable for machines with several brushes,
where it is difficult to centre the abrasive discs.

TABLE FOR CHOOSING THE BRUSHES

Machine
No. Br.
Code
Type of bristles
 Bristles
 Br.
Length
Notes

Innova 60B
1

Innova 65B
2

Innova 75B
2

Innova 85B
2

Innova 100B
2

Innova 70S
1
431774
432423
432425

GREEN PAD 711X355
BLACK PAD 711X355
WHITE PAD 711X355
BROWN PAD 711X355

Innova 70BTO
1

CHOOSING AND USING THE BRUSHES

404627
405630
405629
405628
405627
405519

PPL
PPL
PPL
ABRASIVE

0.3
0.6
0.9

0.9

610
610
610
610
610
585

PAD HOLDER

NYLON

422189
422971
422972
422981
422973

PPL
PPL
PPL
ABRASIVE

0.3
0.6
0.9

340
340
340
340
330

PAD HOLDER

427715
427716
427717
427719
427718

PPL
PPL
PPL
ABRASIVE

0.3
0.6
0.9

390
390
390
390
380

PAD HOLDER

430696
430697
430698
430699
431122

PPL
PPL
PPL
ABRASIVE

0.3
0.6
0.9

430
430
430
430
410

PAD HOLDER

436310
436311
436312
436314
436316

PPL
PPL
PPL
ABRASIVE

0.3
0.6
0.9

510
510
510
510
490

PAD HOLDER

PPL
PPL
MIXED. STEEL ABRASIVE

0.8
1
0.6 + 1
210
690

442663
442664
443713
443714

Sayfa 81

EC DECLARATION OF CONFORMITY 

 
The undersigned manufacturer: 

COMAC S.p.A. 
Via Maestri del Lavoro, 13 
37059 Santa Maria di Zevio (VR) 
declares under its sole responsibility that the products 

 
SCRUBBING MACHINES - mod. 

 
Innova 60 B CB; Innova 65 B CB; Innova 75 B CB; Innova 85 B CB; Innova 100 B CB; Innova 70 S CB; Innova 70 BTO CB 
 
comply with the requirements of the following Directives: 
 
2006/42/EC: Machinery Directive. 
2014/35/EC: Low Voltage Directive. 
2014/30/EC: Electromagnetic compatibility directive. 
 
They also comply with the following standards: 
 
EN 60335-1:2012/A11:2014 
EN 60335-2-72:2012  
EN 12100:2010  
EN 60335-2-29:2004/A2:2010  
EN 61000-6-2:2005/AC:2005  
EN 61000-6-3:2007/A1:2011/AC:2012  
EN 61000-3-2:2014  
EN 61000-3-3:2013  
EN 55014-1:2006/A1:2009/A2:2011  
EN 55014-2:2015  
EN 62233:2008/AC:2008 
 
The person authorized to compile the technical file: 
 
Mr. Giancarlo Ruffo 
Via Maestri del Lavoro, 13 
37059 Santa Maria di Zevio (VR) - ITALY 
 
Santa Maria di Zevio (VR), 24/08/2020 
 
 
 
 
 

81

Comac S.p.A. 
Legal representative 

Giancarlo Ruffo

Sayfa 82

The undersigned manufacturer: 

COMAC S.p.A. 
Via Maestri del Lavoro, 13 
37059 Santa Maria di Zevio (VR) 
declares under its sole responsibility that the products 

 
SCRUBBING MACHINES - mod. 

 
Innova 60 B; Innova 65 B; Innova 75 B; Innova 85 B; Innova 100 B; Innova 70 S; Innova 70 BTO 
 
comply with the requirements of the following Directives: 
 
2006/42/EC: Machinery Directive. 
2014/30/EC: Electromagnetic compatibility directive. 
 
They also comply with the following standards: 
 
EN 60335-1:2012/A11:2014 
EN 60335-2-72:2012  
EN 12100:2010  
EN 61000-6-2:2005/AC:2005  
EN 61000-6-3:2007/A1:2011/AC:2012  
EN 62233:2008/AC:2008 
 
The person authorized to compile the technical file: 
 
Mr. Giancarlo Ruffo 
Via Maestri del Lavoro, 13 
37059 Santa Maria di Zevio (VR) - ITALY 
 
Santa Maria di Zevio (VR), 24/08/2020 
 
 
 
 
 

82

Comac S.p.A. 
Legal representative 

Giancarlo Ruffo

Sayfa 83

UKCA DECLARATION OF CONFORMITY 

 
The undersigned manufacturer: 

COMAC S.p.A. 
Via Maestri del Lavoro, 13 
37059 Santa Maria di Zevio (VR) 
declares under its sole responsibility that the products 

 
SCRUBBING MACHINES - mod. 

 
Innova 60 B CB; Innova 65 B CB; Innova 75 B CB; Innova 85 B CB; Innova 100 B CB; Innova 70 S CB; Innova 70 BTO CB 
 
comply with the requirements of the following Directives: 
 
Supply of Machinery (Safety) Regulations 2008. 
Electrical Equipment (Safety) Regulations 2016. 
Electromagnetic Compatibility Regulations 2016. 
 
They also comply with the following standards: 
 
BS EN 60335-1:2012+A2:2019 
BS EN 60335-2-72:2012  
BS EN 12100:2010  
BS EN 60335-2-29:2004+A11:2018 
BS EN IEC 61000-6-2:2019 
BS EN 61000-6-3:2007+A1:2011  
BS EN IEC 61000-3-2:2019  
BS EN IEC 61000-3-3:2019  
BS EN 55014-1:2017+A11:2020  
BS EN 55014-2:2015  
BS EN 62233:2008 
 
The person authorized to compile the technical file: 
 
Mr. Giancarlo Ruffo 
Via Maestri del Lavoro, 13 
37059 Santa Maria di Zevio (VR) - ITALY 
 
Santa Maria di Zevio (VR), 24/08/2020 
 
 
 
 
 

83

Comac S.p.A. 
Legal representative 

Giancarlo Ruffo

Sayfa 84

The undersigned manufacturer: 

COMAC S.p.A. 
Via Maestri del Lavoro, 13 
37059 Santa Maria di Zevio (VR) 
declares under its sole responsibility that the products 

 
SCRUBBING MACHINES - mod. 

 
Innova 60 B; Innova 65 B; Innova 75 B; Innova 85 B; Innova 100 B; Innova 70 S; Innova 70 BTO 
 
comply with the requirements of the following Directives: 
 
Supply of Machinery (Safety) Regulations 2008. 
 Electromagnetic Compatibility Regulations 2016. 
 
They also comply with the following standards: 
 
BS EN 60335-1:2012+A2:2019 
BS EN 60335-2-72:2012  
BS EN 12100:2010   
BS EN IEC 61000-6-2:2019 
BS EN 61000-6-3:2007+A1:2011   
BS EN 62233:2008 
 
The person authorized to compile the technical file: 
 
Mr. Giancarlo Ruffo 
Via Maestri del Lavoro, 13 
37059 Santa Maria di Zevio (VR) - ITALY 
 
Santa Maria di Zevio (VR), 24/08/2020 
 
 
 
 
 

84

Comac S.p.A. 
Legal representative 

Giancarlo Ruffo

Sayfa 85

Sayfa 86

Sayfa 88

Comac spa 
Via Maestri del Lavoro, 13 - 37059 S.Maria di Zevio (Verona) Italy 
Tel. +39 045 8774222 r.a. - Fax +39 045 8750303 - E-mail:comac@comac.it - www.comac.it